NC1V-1100-0.5AA IDEC, NC1V-1100-0.5AA Datasheet
![CIRCUIT BREAKER, HYD-MAG, 1P, 250V 500mA](/photos/21/79/217996/4667630_sml.jpg)
NC1V-1100-0.5AA
Specifications of NC1V-1100-0.5AA
Related parts for NC1V-1100-0.5AA
NC1V-1100-0.5AA Summary of contents
Page 1
... NC1V Circuit Protectors ...
Page 2
... IDEC's original Spring-up Terminals and Cover Provide IP20 Finger-safe Protection. 17.5 mm (1-pole) Finger-safe, spring-up terminals reduce wiring time. Ring terminal tabs can be installed easily, and screws are held secure. Main Circuit Terminals are Fingersafe (IP20) Spring-up, fingersafe structure requires no terminal cover. ...
Page 3
Auxiliary/Alarm Contact, and Relay Trip Voltage Coil Terminals are Equipped with a Terminal Cover. 35mm-wide DIN Rail Mounting or Direct Panel Mounting Distinguishing Characteristics Wide variety of rated currents and tripping curves. One and 2-pole models are AC/DC compatible and ...
Page 4
... Note 3: Relay trip (voltage trip) type is not equipped with an overcurrent trip function. • Do not use the NC1V circuit protectors in environments where they are exposed to extreme temperature, humidity, dust, corrosive gases, vibration, shock circuit where inrush current may be present, otherwise unnecessary operations and damage may occur. ...
Page 5
... Type No. Development NC1V - 30A A DC24V 1 Type NC1V: Flap actuator type DIN rail and panel mounting 2 No. of Poles 1: 1-pole 2: 2-pole 3: 3-pole 3 Internal Circuit 1: Series trip (current trip) 5: Relay trip (voltage trip) 4 Auxiliary/Alarm Contacts 00: None 11: With one auxiliary contact 12: With two auxiliary contacts ...
Page 6
... NC1V Circuit Protectors Internal Circuit • 1-pole NC1V-1100 (Without auxiliary/alarm contacts) (With auxiliary contact) LINE LINE LOAD LOAD • 2-pole NC1V-2100 (Without auxiliary/alarm contacts) (With auxiliary contact) LINE LINE LINE LOAD LOAD LOAD Note: Those with two auxiliary contacts and with one auxiliary contact and one alarm contact have been applied for UL and CCC. ...
Page 7
... Current (percent load of the rated current) 1000 100 10 1 0.1 0.01 100 200 300 400 500 600 125 Current (percent load of the rated current) NC1V Circuit Protectors 1000 Curve A (medium) 100 10 1 0.1 0.01 700 800 900 1000 100 200 125 Current (percent load of the rated current) Note: The entire shaded area applies to AC ...
Page 8
... NC1V Circuit Protectors Time Delay Curve and Ambient Temperature NC1V circuit protectors employ an electromagnetic tripping system, where the rated current (trip current) is not affected by ambient temperatures. But the time delay may vary with the oil viscosity in the oil dash pot. Lower oil viscosity at higher temperatures results in a shorter delay, whereas at lower temperatures the delay will be longer ...
Page 9
... M4 Terminal Srew 29.5 (up to 20A) M5 Terminal Screw (25A or more) NC1V-2100 ON 2-ø4.5 Holes (for screw mounting) 35.0 NC1V Circuit Protectors DIN Rail (BNDN1000) 6.6 66.0 48.3 5.0 33.0 DIN Rail (BNDN1000) 6.6 66.0 48.3 5.0 33.0 ...
Page 10
... NC1V-2111 (one auxiliary contact) NC1V-2112 (two auxiliary contacts) NC1V-2121 (one alarm contact) ON NC1V-2131 (one auxiliary contact and one alarm contact) 35.0 The dimensions are for NC1V-2111 and NC1V-2121. 29.5 NC1V-2500 (Relay Trip) ON 35.0 • 3-pole 47.0 NC1V-3100 ON 52.5 NC1V-3111 (one auxiliary contact) 47 ...
Page 11
... For wiring the main circuit terminal, use the applicable crimp terminals and tighten to the recommended torque. • When using the NC1V circuit protector as CSA-certified product, use with CSA- certified crimp terminal. 90% • When using the NC1V circuit protector as UL-listed product, use with UL-listed crimp terminal ...
Page 12
... NC1V Circuit Protectors Accessories • DIN Rail 35mm-wide DIN Rails Length Part No. 1000mm BNDN1000 • End Clip Part No. BNL6 9mm wide • Auxiliary/Alarm Terminal Cover • Miscellaneous Accessories (available 2009) Type No. Description NC9Z-MA11 Panel Cut-Out Mounting bracket for 1-pole mode NC9Z-MA21 ...