PS21997-4 Powerex Inc, PS21997-4 Datasheet - Page 5

• Manufacturer Part Number: PS21997-4
• Description: INTELLIGENT POWER MODULE, 600V, 30A, DIP
• Manufacturer: Powerex Inc
• Series: Intellimod™r
• Type: IGBTr

Specifications of PS21997-4

• Dc Collector Current: 30A
• Collector Emitter Voltage Vces: 600V
• Power Dissipation Pd: 47.6W
• Collector Emitter Voltage V(br)ceo: 600V
• Operating Temperature Range: -20°C To +125°C
• No. Of Pins: 25
• Configuration: 3 Phase
• Current: 30A
• Voltage: 600V
• Voltage - Isolation: 1500VDC
• Package / Case: PCB Module
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Other names: 835-1044

PS21997-4, PS21997-4A
Intellimod™ Module
Dual In-line Intelligent Power Module
30 Amperes/600 Volts
Application Circuit
10/09
Powerex, Inc., 173 Pavilion Lane, Youngwood, Pennsylvania 15697-1800 [phone]
+3.3 to +5V
Component Selection:
Dsgn.
D 1
DZ 1
C 1
C 2
C 3
C 4
C 5
C 6
C SF
R SF
R SHUNT
R 1
R 2
R 3
Notes:
10) Use high quality, tight tolerance current sensing resistor. Connect resistor as close as possible to the DIP’s N terminal. Be careful
1) To prevent input signal oscillations minimize wiring length to controller (~2cm). Additional RC filtering (C5 etc.) may be required.
2) Internal HVIC provides high voltage level shifting allowing direct connection of all six driving signals to the controller.
3) F O output is an open collector type. Pull up resistor (R3) should be adjusted to current sink capability of the controller.
4) Use only one V NC Pin (either 9 or 16) and leave the other open.
5) Boot strap supply component values must be adjusted depending on the PWM frequency and technique.
6) Wiring length associated with R SHUNT , R SF , C SF must be minimized to avoid improper operation of the OC function.
7) R SF , C SF set over current protection trip time. Recommend time constant is 1.5µs-2.0µs. See application notes.
8) Local decoupling/high frequency filter capacitors must be connected as close as possible to the modules pins.
9) The length of the DC link wiring between C5, C6, the DIP’s P terminal and the shunt must be minimized to prevent excessive
If filtering is added be careful to maintain proper dead time and voltage levels. See application notes for details.
transient voltages. In particular C6 should be mounted as close to the DIP as possible.
to check for proper power rating. See application notes for calculation of resistance value.
This symbol indicates
connection to ground plane.
Typ. Value
1A, 600V
24V, 1.0W
10-100uF, 50V
0.22-2.0uF, 50V
10-100uF, 50V
100pF, 50V
200-2000uF, 450V
0.1-0.22uF, 450V
1000pF, 50V
1.8k ohm
5-100mohm
10 ohm
330 ohm
10k ohm
R 3
R 2
+15V
R 1
R 1
R 1
+
C 4
R 2
R 2
C 3
D 1
D 1
D 1
C 2
R 2
R 2
C 1
C 1 DZ 1
C 1 DZ 1
C 4
C 4
C SF
+
+
+
R 2
R 2
DZ 1
C 4
C 4
DZ 1
Description
Boot strap supply diode – Ultra fast recovery
Control and boot strap supply over voltage suppression
Boot strap supply reservoir – Electrolytic, long life, low Impedance, 105°C (Note 5)
Local decoupling/High frequency noise filters – Multilayer ceramic (Note 8)
Control power supply filter – Electrolytic, long life, low Impedance, 105°C
Optional Input signal noise filter – Multilayer ceramic (Note 1)
Main DC bus filter capacitor – Electrolytic, long life, high ripple current, 105°C
Surge voltage suppression capacitor – Polyester/Polypropylene film (Note 9)
Short circuit detection filter capacitor – Multilayer Ceramic (Note 6, Note 7)
Short circuit detection filter resistor (Note 6, Note 7)
Current sensing resistor – Non-inductive, temperature stable, tight tolerance (Note 10)
Boot strap supply inrush limiting resistor (Note 5)
Optional control input noise filter (Note 1, Note 2)
Fault output signal pull-up resistor (Note 3)
C 2
C 4
C 4
R SF
C 2
C 2
C 2
V WFB
V UFB
V VFB
V N1
V NC
V NC
C IN
V P1
NC
W N
F O
W P
U N
U P
V P
V N
17
1
OVER CURRENT
+V CC
CONDITIONING
INPUT SIGNAL
PROTECTION
LEVEL
LEVEL
LEVEL
FAULT LOGIC
SHIFT
SHIFT
SHIFT
+V CC
LVIC
HVIC
PROT.
GATE DRIVE
GATE DRIVE
GATE DRIVE
UV
UV PROT.
UV PROT.
UV PROT.
25
18
P
U
V
W
N
R SHUNT
MOTOR
AC LINE
C 5
C 6
+
+
5