Q6008LH4 Littelfuse Inc, Q6008LH4 Datasheet - Page 6
![ALTERNISTOR, 600V, 8A, TO-220](/photos/19/7/190743/3833580_sml.gif)
Q6008LH4
Manufacturer Part Number
Q6008LH4
Description
ALTERNISTOR, 600V, 8A, TO-220
Manufacturer
Littelfuse Inc
Datasheet
1.Q6025L6.pdf
(10 pages)
Specifications of Q6008LH4
Peak Repetitive Off-state Voltage, Vdrm
600V
Gate Trigger Current Max (qi), Igt
35mA
On State Rms Current It(rms)
8A
Peak Non Rep Surge Current Itsm 50hz
83A
Holding Current Max Ih
35mA
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Alternistor Triacs
(10) See Figure E4.12 for t
(11) See package outlines for lead form configurations. When ordering
(12) Initial on-state current = 400 mA dc for 16 A to 40 A devices and
(13) See Figure E4.1 through Figure E4.4 for maximum allowable case
(14) Pulse width ≤10 µs;
(15) For 6 A to 12 A devices, R
(16) 40 A pin terminal leads on K package can run 100 °C to 125 °C.
(17) Alternistor does not turn on in Quadrant IV.
(18) T
(19) I
(20) Minimum non-trigger V
Gate Characteristics
Teccor triacs may be turned on in the following ways:
•
•
In all cases, if maximum surge capability is required, gate pulses
should be a minimum of one magnitude above minimum I
ing with a steep rising waveform (≤1 µs rise time).
If QIV and QI operation is required (gate always positive), see
Figure AN1002.8, “Amplified Gate” Thyristor Circuit.
* UL Recognized Product per UL File E71639
** For 4000 V isolation, use V suffix in part number.
http://www.littelfuse.com
+1 972-580-7777
Package Code
In-phase signals (with standard AC line) using Quadrants I
and III
Application of unipolar pulses (gate always negative), using
Quadrants II and III with negative gate pulses
special lead forming, add type number as suffix to part number.
100 mA for 6 A to 12 A devices.
temperature at maximum rated current.
devices with gate pulse having rise time of ≤0.1 µs.
GT
C
Type
10 A
12 A
16 A
25 A
30 A
35 A
40 A
= T
= 200 mA for 6 A to 12 A devices and 500 mA for 16 A to 40 A
6 A
8 A
J
for test conditions in off state
I
GT
Isolated *
TO-218
gt
GT
1.35
0.97
≤ I
versus I
K
GTM
at 125 °C is 0.2 V.
L
= 60 Ω; 16 A and above, R
GT
.
TO-218X
Isolated *
1.32
0.95
J
Thermal Resistance (Steady State)
L
R
= 30 Ω
θ JC
GT
Isolated **
rat-
TO-220
3.3 [50]
[R
2.8
2.6
2.3
2.1
2.0
2.3
L
θ JA
E4 - 6
] (TYP.) °C/W
Definition of Quadrants
Electrical Isolation
Teccor’s isolated alternistor packages withstand a minimum high
potential test of 2500 V ac rms from leads to mounting tab, over
the operating temperature range of the device. The following iso-
lation table shows standard and optional isolation ratings.
* UL Recognized File E71639
** For 4000 V isolation, use V suffix in part number.
V AC RMS
2500
4000
Non-Isolated
1.80 [45]
TO-220
I
1.50
1.30
1.20
1.10
0.87
0.85
G T
R
(
(
-
-
-
)
)
I
GATE
I
GATE
G T
G T
from Leads to Mounting Tab *
Isolated
Standard
ALL POLARITIES ARE REFERENCED TO MT1
NOTE: Alternistors will not operate in QIV
TO-218
REF
REF
MT2
MT2
N/A
Electrical Isolation
MT1
MT1
TO-252
D-Pak
2.1
1.8
(Negative Half Cycle)
(Positive Half Cycle)
D
MT2 NEGATIVE
MT2 POSITIVE
QIII
QII
+
-
QI
QIV
Optional **
Isolated
Standard
TO-220
(+)
(+)
2.3 [64]
TO-251
I
GATE
V-Pak
I
GATE
G T
Thyristor Product Catalog
2.1
G T
V
©2004 Littelfuse, Inc.
MT2
REF
MT2
REF
MT1
MT1
TO-218X
Isolated
Standard
Data Sheets
+
TO-263
D
N/A
1.80
1.50
1.30
1.20
1.10
0.87
2
I
N
G T
Pak