D041 ETERNA, D041 Datasheet - Page 2

• Manufacturer Part Number: D041
• Description: DOWNLIGHT, L/V, POLISHED CHROME
• Manufacturer: ETERNA

Specifications of D041

• Light Source: Tungsten Halogen
• Depth: 27mm
• Svhc: No SVHC (15-Dec-2010)
• Base Type: G4 (M47) 20W
• Behind Panel Depth: 27mm
• Colour: Polished Chrome
• External Diameter: 70mm
• External Length / Height: 27mm
• External Width: 70mm

Read this first:
>
>
>
>
>
>
>
>
>
>
>
>
>
>
>
>
Safety markings:
If in any doubt, consult a qualified
electrician.
Suitable for indoor use only.
This product is only suitable for use in living
areas ( not for areas constantly subject to
moisture ).
This product is suitable for installation on
surfaces with normal flammability ( indicated by
the "F" in a triangle ) e.g. wood, plasterboard,
masonry. It is not suitable for use on highly
flammable
textiles ).
Use only with a suitable 240V / 12V step down
transformer.
Do not connect lights directly to the mains.
Do not overload the transformer, check that the
total Wattage of all fittings does not exceed the
maximum marked on the transformer.
Before making fixing hole(s), check that there
are no obstructions hidden beneath the
mounting surface such as pipes or cables.
Make sure that the fixings are strong enough to
support the considerable weight of the fitting
and hold it rigidly.
If the location of your new fitting requires the
provision of a new electrical supply, the supply
must conform with the requirements of the
latest edition of the IEE wiring regulations.
Do not cover the fitting and / or transformer
with any insulating materials.
This fitting uses SELV ( Safety Extra Low
Voltage ). Do not connect any part to earth.
The fitting must be positioned so that there is at
least 0.3m ( 300mm ) between the bulb and
any illuminated surface.Do not use the fitting
without the safety shield fitted.
When replacing the lamp, do not touch with
bare fingers, grip the lamp with a tissue or
clean soft cloth.
Do not attach to surfaces which are damp,
freshly
conductive (e.g. metallic surfaces).
If in any doubt, consult a qualified
electrician.
painted
surfaces
or
otherwise
(
e.g.
polystyrene,
electrically
Installation:
SURFACE
1)
2)
3)
4)
5)
6)
7)
8)
RECESSED
1)
2)
Check that the transformer you intend to use to
power your fitting is adequately rated for the
total number of fittings you are installing and
that it has been installed in accordance with all
of the manufacturers instructions.
Choose the location for your new fitting.
Prepare the route for the cable between the
light and the transformer.
Extract the light from its surround by gently
levering it out using a small screwdriver or
other flat bladed implement. Take great care
not to damage the decorative finish.
With the cable threaded through the surround,
secure the surround in position using suitable
fixings appropriate to the mounting surface.
Gently pull the cable through your prepared exit
route and press the light fitting back into the
surround. Make sure that you do not trap a loop
of cable behind the light fitting.
Make the connection of the cable to the
transformer. We recommend the use of an
Eterna Lighting transformer which has sockets
designed to allow the plug fitted to your light to
plug directly in.
Note: If you have any other transformer in
which there is no provision for connection using
the plug fitted to your light, you will need to cut
the plug off and use an alternative method of
connection. The connections to the light fitting
are not designated Live or Neutral. Make
connections using a terminal block, ensure that
there are no strands of wire protruding and
wrap well with insulating tape.
Restore the power and switch on.
Check that the transformer you intend to use to
power your fitting is adequately rated for the
total number of fittings you are installing and
that it has been installed in accordance with all
of the manufacturers instructions.
Choose the location for your new fitting.
3)
4)
5)
6)
7)
8)
Assembling the plug:
>
Prepare the route for the cable between the
light and the transformer.
Extract the light from its surround by gently
levering it out using a small screwdriver or
other flat bladed implement. Take great care
not to damage the decorative finish.
Make a hole in the mounting surface of 61mm
diameter.
Gently pull the cable through your prepared exit
route and press the light fitting back into the
mounting surface. Make sure that you do not
trap a loop of cable behind the light fitting.
Make the connection of the cable to the
transformer. We recommend the use of an
Eterna Lighting transformer which has sockets
designed to allow the plug fitted to your light to
plug directly in.
Note: If you have any other transformer in
which there is no provision for connection using
the plug fitted to your light, you will need to cut
the plug off and use an alternative method of
connection. The connections to the light fitting
are not designated Live or Neutral. Make
connections using a terminal block, ensure that
there are no strands of wire protruding and
wrap well with insulating tape.
Restore the power and switch on.
Once you have threaded the cables from your light to your transformer,
you will need to push the pins at the ends of your cables into the plug
body. Note, once the pins have been inserted they cannot be removed.
Prize out glass and
ring with flat blade
Important !
Never touch the glass when the light is switched on.
Allow light to cool before changing the bulb
Hole cut out required: 61mm diameter.
61mm