1260-07 IMATRONIC, 1260-07 Datasheet - Page 3

• Manufacturer Part Number: 1260-07
• Description: LASER, GATED CAMEO, 650NM, 1MW
• Manufacturer: IMATRONIC

Specifications of 1260-07

• Wavelength Typ: 650nm
• Output Power: 1mW
• Laser Beam Size: 2mm
• Supply Current: 45mA
• Voltage Rating: 6V
• Beam Divergence: 0.2mrad
• External Diameter: 14mm
• External Length / Height: 24mm
• External Width: 14mm
• Laser Lens: Aperture
• Rohs Compliant: Yes
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

STANDARD WAVELENGTHS AND POWER
OPTIONS
stated
MECHANICAL SPECIFICATIONS
Dimensions (L x W x H)
Housing
Isolated Body
Input Leads
Lead length
OPTICAL SPECIFICATIONS
Diode Power
Wavelength
Power Stability
Wavelength vs Temp
Bore sighting
Focus Range
Astigmastism
Beam Alignment
Pointing Stability
ENVIRONMENTAL SPECIFICATIONS
Operating Tempertaure
Storage temp
Operating Humidity (%RH)
MTTF at 25°C
DYNAMIC OUPUT
Control input rise / fall time
Enable input delay time
ELECTRICAL SPECIFICATIONS
Input voltage (+ve) Red
Input voltage (-ve) Black
Control Lead Yellow (1260 only)
Enable Lead Blue (1260 only)
Connector type
Reverse - Polarity protection
Operating Current
Specifi cations are typical at 25°C unless otherwise
635nm
650nm
670nm
780nm
Custom
Please note wavelength tolerance can vary typicaly by + 10nm.
1250 version
1260 version
1250 version
1260 version
1, 3 mW
1, 3 mW
1, 3 mW
1,3 mW
Please call for further details
front and black plastic
back.
(0V)
(0V), Yellow (control),
Blue (enable)
24 x 14 x 14
Brass M12 thread
Yes
2, Red (+ve) Black
4, Red (+ve) Black
300mm
1 mW to 3 mW
635 nm to 780 nm *
0.15 % / °C
< 3mrad
30mm to infi nity *
30 µm
5 mrad
10 µrad
-10°C to +40°C
-25°C to +85°C
90
25,000 hours
5 µs
2 ms
3.0 Vdc to 6 Vdc
0 V
off < 50 mV on > 2.0V
off <0.4 V on > 2.0 V
JST 2 pin
JST 4 pin
Yes
35 to 45 mA
0.25nm / °C
Cameo Laser Series
convenient mounting method which also provides
effective cooling of the laser diode to maximise the
operating life. The metal body should be in good thermal
contact with the mount, which should not be allowed to
exceed the maximum case temperature.
photodetectors, cameras and other non-visual sensing
is the ability to rapidly switch the laser output ON and
OFF. Simply applying and removing the supply voltage is
rarely satisfactory and in certain cases can result in the
destruction of the module. This is because laser diodes
are very sensitive to spikes and surges, which are often
the result of uncontrolled supply switching. To overcome
this limitation, the 1260 gated Cameo has two additional
inputs that are provided to control the output of the laser
module in a reliable and predictable way.
switching. The 1260 series eliminates the requirement to
provide an external switching device by providing a logic
compatible enable input, capable of operating from low
power logic and micro-processors. In this OFF condition,
the module draws virtually no current and no light is
emitted.
second input is provided which directly controls the laser
output. This input may be used in either of two ways,
digital and analog control.
However, applying a HIGH turns the laser ON after a
control input delay. The output rise time after this delay
is then much faster. This sets the maximum rate at which
the module can switch fully ON and OFF.
analog control, the output power can be changed from
the maximum rated power to a low level, typically 1-2%
of the maximum. By preventing the laser output turning
OFF completely, there are no delays and the frequency
response is maximised
be modulated or synchronised by using an external
signal. Required voltage range is 0 to +1 Vdc (to set the
maximum intensity), frequency range is DC to 100 KHz.
MOUNTING
The M12 x 1 threaded body provides a stable and
GATED CAMEO APPLICATION GUIDE
Introduction
A common requirement for applications which use
Input Description
Some applications require a simple, slow speed ON/OFF
In applications which require higher speed switching, a
Digital Control
A logic LOW level turns the output completely OFF.
Analog Control
This is the fastest way to control the laser output. With
Modulation & Synchronization
Using the yellow control lead the gate cameo laser may
Global Laser - CAMEO
Page -3-