120053 MARL, 120053 Datasheet - Page 6

• Manufacturer Part Number: 120053
• Description: LED, SMD, 120DEG, BLUE
• Manufacturer: MARL

Specifications of 120053

• Led Colour: Blue
• Luminous Intensity: 104mcd
• Viewing Angle: 120°
• Forward Voltage: 3.6V
• Led Mounting: SMD
• Lens Shape: Oval
• Wavelength Typ: 470nm
• Dominant Wavelength: 470nm
• External Depth: 1.5mm
• External Length /: RoHS Compliant
• Forward Current If: 20mA
• Svhc: No SVHC (15-Dec-2010)
• Rohs Compliant: Yes

(4) Soldering Conditions
(5) Cleaning
2.5 ~ 5°C / sec.
· The LEDs can be soldered in place using the reflow soldering method.
· Recommended soldering conditions
· Occasionally there is a brightness decrease caused by the influence of heat or ambient atmosphere
· The encapsulated material of the LEDs is silicone. Therefore the LEDs have a soft surface on the
· Repairing should not be done after the LEDs have been soldered.
· Reflow soldering should not be done more than two times.
· When soldering, do not put stress on the LEDs during heating.
· After soldering, do not warp the circuit board.
· It is recommended that isopropyl alcohol be used as a solvent for cleaning the LEDs.
· Do not clean the LEDs by the ultrasonic.
guarantee on the LEDs after they have been assembled using the dip soldering method.
[Temperature-profile (Surface of circuit board) ]
during air reflow.
top of package.
Precautions should be taken to avoid the strong pressure on the encapsulated part.
the chip mounter, the picking up nozzle that does not affect the silicone resin should be used.
a double-head soldering iron should be used.
characteristics of the LEDs will or will not be damaged by repairing.
other solvents, it should be confirmed beforehand whether the solvents will dissolve the package and the
resin or not.
cleaning on the LEDs depends on factors such as ultrasonic power and the assembled condition.
Before cleaning, a pre-test should be done to confirm whether any damage to the LEDs will occur.
Pre-heat
Pre-heat time
Peak
Soldering time
Condition
# After reflow soldering rapid cooling should be avoided.
[Recommended soldering pad design]
temperature
<
1
: Lead Solder>
2.5 ~ 5°C / sec.
120 ~ 150°C
120sec.Max.
Pre-heating
1.5
4.4
120 ~ 150°C
120 sec. Max.
240°C Max.
10 sec. Max.
refer to
Freon solvents should not be used to clean the LEDs because of worldwide regulations.
Temperature - profile
The pressure to the top surface will be influence to the reliability of the LEDs.
Lead Solder
It is recommended that the User use the nitrogen reflow method.
60sec.Max.
Above 200
Reflow Soldering
2.2
°C
(Unit : mm)
240°C Max.
10sec. Max.
1
.
180 ~ 200°C
120 sec. Max.
260°C Max.
10 sec. Max.
refer to
(N
Temperature - profile
2
reflow is recommended.)
Lead-free Solder
When it is absolutely necessary, the influence of ultrasonic
Use the following conditions shown in the figure.
It should be confirmed beforehand whether the
-5-
Use the conditions shown to the under figure.
1 ~ 5°C / sec.
<
2
: Lead-free Solder>
2
.
Temperature
Soldering time
1 ~ 5°C / sec.
180 ~ 200°C
120sec.Max.
Pre-heating
When repairing is unavoidable,
Hand Soldering
Nichia cannot make a
60sec.Max.
Above 220°C
Nichia STSE-CC2008B
350°C Max.
3 sec. Max.
(one time only)
So when using
<Cat.No.040528>
260°C Max.
10sec. Max.
When using