HCPL-7560-000E Avago Technologies US Inc., HCPL-7560-000E Datasheet
![no-image](/images/manufacturer_photos/0/0/86/avago_technologies_us_inc__sml.jpg)
HCPL-7560-000E
Specifications of HCPL-7560-000E
Available stocks
Related parts for HCPL-7560-000E
HCPL-7560-000E Summary of contents
Page 1
... Mode 2 with HCPL-0872) • 8-bit Effective Resolution with 5µs Signal Delay (14-bit with 102 µs) (with HCPL-0872) • Fast 3 µs Over-Range Detection (with HCPL-0872) • ± 200 mV Input Range with Single 5 V Supply • 5% Internal Reference Voltage Matching • Offset Calibration (with HCPL-0872) • ...
Page 2
... To order, choose a part number from the part number column and combine with the desired option from the option column to form an order entry. Example 1: HCPL-7560-560E to order product of Gull Wing Surface Mount package in Tape and Reel packaging with IEC/EN/ DIN EN 60747-5-2 Safety Approval in RoHS compliant. Example 2: HCPL-7560 to order product of 300 mil DIP-8 package in tube packaging and non-RoHS compliant ...
Page 3
... DIMENSIONS IN MILLIMETERS AND (INCHES). NOTE: FLOATING LEAD PROTUSION IS 0.5 mm (20 mils) MAX. NOTE: INITIAL OR CONTINUED VARIATION IN THE COLOR OF THE HCPL-7560’S WHITE MOLD COMPOUND IS NORMAL AND DOES NOT AFFECT DEVICE PERFORMANCE OR RELIABILITY. 8-pin Gull Wing Surface Mount Option 300 9.80 ± ...
Page 4
Solder Reflow Temperature Profile 300 PREHEATING RATE 3˚C + 1˚C/-0.5˚C/SEC. REFLOW HEATING RATE 2.5˚C ± 0.5˚C/SEC. 200 160˚C 150˚C 140˚C 100 ROOM TEMPERATURE 0 0 Note: Use of non-chlorine-activated fluxes is highly recommended. Recommended Pb-Free IR Profile 260 +0/-5˚C T ...
Page 5
... Regulatory Information The HCPL-7560 has been approved by the following organizations: IEC/EN/DIN EN 60747-5-2 Approved under: IEC 60747-5-2:1997 + A1:2002 EN 60747-5-2:2001 + A1:2002 DIN EN 60747-5-2 (VDE 0884 Teil 2):2003-01. UL Approval under UL 1577, component recognition program CSA Approval under CSA Component Acceptance Notice #5, File CA 88324. IEC/EN/DIN EN 60747-5-2 Insulation Characteristics Description Installation classification per DIN VDE 0110/1 ...
Page 6
... Two Second Transient Input Voltage Output Voltages Lead Solder Temperature Solder Reflow Temperature Profile Recommended Operating Conditions Parameter Ambient Operating Temperature Supply Voltages Input Voltage 6 HCPL-7560 Units Conditions 7.4 mm Measured from input terminals to output terminals, shortest distance through air. 8.0 mm Measured from input terminals to output terminals, shortest distance path along body ...
Page 7
... Output Logic Low Voltage Output Short Circuit Current Input Supply Current Output Supply Current Output Clock Frequency Data Hold Time Electrical Specifications (Tested with HCPL-0872 or Sinc Unless otherwise noted, all specifications are at V specifications are 25°C and V A over the following ranges -40° ...
Page 8
... Dynamic Characteristics (Digital Interface IC HCPL-0872 is set to Conversion Mode 5.) Parameter Symbol Signal-to-Noise Ratio SNR Total Harmonic Distortion THD Signal-to-(Noise + Distortion) SND Effective Number of Bits ENOB Conversion Time Signal Delay t DSIG Over-Range Detect Time t OVR1 Threshold Detect Time t THR1 (default configuration) Signal Bandwidth ...
Page 9
Notes (pin 3) is brought above with respect to GND1 an IN- DD1 internal optical-coupling test mode may be activated. This test mode is not intended for customer use. 2. Avago Technologies recommends ...
Page 10
Figure 4.5 V DD1 V = 5.0 V ...
Page 11
CONVERSION MODE # Figure 10. SNR vs. Conversion Mode. 100 CONVERSION MODE ...
Page 12
... NON-ISOLATED + DD1 DD2 V MCLK IN+ V MDAT IN- C2 GND1 GND2 0.1 µF HCPL-7560 CCLK V DD CLAT CHAN CDAT SCLK 3-WIRE MCLK1 SDAT SERIAL INTERFACE MDAT1 CS + MCLK2 THR1 C3 MDAT2 OVR1 10 µF GND RESET HCPL-0872 ...
Page 13
... HCPL-7560 can be used together with HCPL-0872, Digital Interface digital filter. The primary func- tions of the HCPL-0872 Digital Interface IC are to derive a multi-bit output signal by averaging the single-bit modulator data, as well as to provide a direct micro- controller interface. The effective resolution of the ...
Page 14
... R1 should be chosen to supply sufficient current from the existing floating supply. The voltage from the cur- rent sensing resistor or shunt (Rsense) is applied to the input of the HCPL-7560 (U2) through an RC anti-aliasing filter (R2 and C2). And finally, the output clock and data of the isolated modulator are connected to the digital interface IC ...
Page 15
PC Board Layout The design of the printed circuit board (PCB) should follow good layout practices, such as keeping bypass capacitors close to the supply pins, keeping output signals away from input signals, the use of ground and power planes, ...
Page 16
Because of the Kelvin connection, any voltage drops across the leads ...
Page 17
... 5.1 V 0.1 µF V DD1 V IN+ V IN- GND1 C2a C2b 0.01 µF 0.01 µF HCPL-7560 Motor Power Range 120 V -440 [ [14 - 53] V ...
Page 18
... Voltage Sensing The HCPL-7560 Isolated Modulator can also be used to isolate signals with amplitudes larger than its recom- mended input range with the use of a resistive voltage divider at its input. The only restrictions are that the impedance of the divider be relatively small (less than 1 kW) so that the input resistance (280 kW) and input bias current (1µ ...