HCPL-070L-560E Avago Technologies US Inc., HCPL-070L-560E Datasheet - Page 10
![no-image](/images/manufacturer_photos/0/0/86/avago_technologies_us_inc__sml.jpg)
HCPL-070L-560E
Manufacturer Part Number
HCPL-070L-560E
Description
DARLINGTON-NPN-OUTPUT DC-INPUT OPTOCOUPLER,1-CHANNEL,3.75KV ISOLATION,SO
Manufacturer
Avago Technologies US Inc.
Datasheet
1.HCPL-073L-000E.pdf
(12 pages)
Specifications of HCPL-070L-560E
Voltage - Isolation
3750Vrms
Number Of Channels
1, Unidirectional
Current - Output / Channel
60mA
Data Rate
100KBd
Propagation Delay High - Low @ If
30µs @ 500µA
Current - Dc Forward (if)
20mA
Input Type
DC
Output Type
Open Collector
Mounting Type
Surface Mount
Package / Case
8-SOIC (0.154", 3.90mm Width)
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
HCPL-070L-560E
Manufacturer:
AVAGO
Quantity:
40 000
Package Characteristics
Parameter
Input-Output
Momentary
Withstand
Voltage**
Resistance
(Input-Output)
Capacitance
(Input-Output)
Input-Input
Insulation
Leakage Current
Input-Input
Insulation
Leakage Current
Capacitance
(Input-Input)
*All typical values at TA = 25˚C, unless otherwise noted.
**The Input-Output Momentary Withstand Voltage is a dielectric voltage rating that should not be interpreted as an input-output continuous
voltage rating. For the continuous voltage rating refer to the IEC/EN/DIN EN 60747-5-2 Insulation Characteristics Table (if applicable), your equip-
ment level safety specification or Avago Application Note 1074 entitled "Optocoupler Input-Output Endurance Voltage."
Notes:
1. Pin 5 should be the most negative voltage at the detector side.
2. Each channel.
3. DC CURRENT TRANSFER RATIO (CTR) is defined as the ratio of output collector current, I
4. Device considered a two-terminal device: pins 1, 2, 3, and 4 shorted together, and pins 5, 6, 7, and 8 shorted together.
5. Measured between pins 1 and 2 shorted together, and pins 3 and 4 shorted together.
6. Common mode transient immunity in a Logic High level is the maximum tolerable (positive) dV
7. In applications where dV/dt may exceed 50,000 V/µs (such as static discharge) a series resistor, R
8. Use of a 0.1 µF bypass capacitor connected between pins 5 and 8 adjacent to the device is recommended.
9. In accordance with UL 1577, each optocoupler is proof tested by applying an insulation test voltage > 4500 V rms for 1 second (leakage detec-
10. In accordance with UL 1577, each optocoupler is proof tested by applying an insulation test voltage > 6000 V rms for 1 second (leakage detec-
11. Measured between the LED anode and cathode shorted together and pins 5 through 8 shorted together.
12. Derate linearly above 65˚C free-air temperature at a rate of 2.3 mW/˚C for the SO-8 package.
10
sure that the output will remain in a Logic High state (i.e., V
maximum tolerable (negative) dV
(i.e., V
IC from destructively high surge currents. The recommended value is R
tion current limit, I
tion current limit, I
O
< 0.8 V).
I-O
I-O
< 5 µA).
< 5 µA).
Sym.
V
R
C
I
R
C
I-I
ISO
I-O
I-O
I-I
I-I
Device HCPL-
270L
273L
070L
073L
CM
/dt of the common mode pulse, V
Min.
3750
0.005
O
Typ.*
10
0.6
10
0.03
0.25
> 2.0 V). Common mode transient immunity in a Logic Low level is the
12
11
Max.
CM
CC
, to assure that the output will remain in a Logic Low state
= 110 Ω.
Units
V rms
Ω
pF
µA
Ω
pF
O
, to the forward LED input current, I
Test Conditions
RH ≤ 50%,
t = 1 min.,
T
V
RH ≤ 45%
f = 1 MHz
RH ≤ 45%
V
A
CM
I-O
I-I
CC
= 25˚C
, should be included to protect the detector
= 500 Vdc
/dt of the common mode pulse, V
= 500 Vdc
Fig.
F
, times 100%.
Note
4, 9
4
11
5
5
5
CM
, to as-