43020-2000 Molex Inc, 43020-2000 Datasheet - Page 2
![CONN PLUG 20POS 3MM DUAL ROW](/photos/4/9/40928/43020-2000_sml.jpg)
43020-2000
Manufacturer Part Number
43020-2000
Description
CONN PLUG 20POS 3MM DUAL ROW
Manufacturer
Molex Inc
Series
Micro-Fit 3.0™ 43020r
Specifications of 43020-2000
Pitch
0.118" (3.00mm)
Number Of Rows
2
Connector Type
Plug
Contact Type
Male Pin
Number Of Positions
20
Row Spacing
0.118" (3.00mm)
Mounting Type
Panel Mount, Snap-In
Contact Termination
Crimp
Fastening Type
Ramp
Color
Black
Note
Contacts Not Provided
Product Type
Plugs - Housings
Contact Gender
Pin (Male)
Number Of Positions / Contacts
20
Mounting Style
Free Hanging
Mounting Angle
Vertical
Termination Style
Crimp
Housing Material
Polyester
Voltage Rating
350 V
Current Rating
5 A
Gender
Plug
No. Of Contacts
20
No. Of Rows
2
Pitch Spacing
3mm
Connector Mounting
Panel
Contact Material
Phosphor Bronze
Contact Plating
Tin
Rohs Compliant
Yes
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Features
-
Lead Free Status / Rohs Status
Lead free / RoHS Compliant
Other names
043020-2000
043020-2000-P
0430202000
0430202000-P
43020-2000-P
430202000
430202000-P
WM2486
043020-2000-P
0430202000
0430202000-P
43020-2000-P
430202000
430202000-P
WM2486
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
43020-2000
Manufacturer:
MOLEX
Quantity:
40 044
REVISION:
DOCUMENT NUMBER:
5.0 TESTING PROCEDURES
A
5.1 TERMINAL RETENTION FORCE
5.2 THUMB LATCH TO RAMP YIELD STRENGTH
5.3 THUMB LATCH DURABILITY/CYCLING
TS-43045-003
Microfit 43030 and 43031 terminals were crimped to 20 awg wires and inserted into receptacle
and plug housings, respectively. All circuits were populated. An axial pullout force was applied to
each terminal by pulling on the wire at a rate of 1.0 inch per minute. The maximum force to
dislodge each terminal from the housing was recorded.
Receptacles were mated to header housings to fully engage latches. Header housings were
secured to the base table and the receptacle housings were secured within a grip fixture attached
to the load cell of a motorized force testing device. The crosshead of the device was then moved
in the direction of unmating at a rate of 1.0 inch per minute until the latching geometry of either
the receptacle or the header housing yielded. The maximum force to yield the latch was
recorded.
The thumb latch on the receptacle was first deflected to its extreme until it contacted the body of
the housing (wire insertion side). It was then deflected to its opposite extreme until it contacted
the towers of the housing (mating side). This defined one cycle of the latch. Increments of 5
cycles were repeated on the latch. After each 5 cycle increment the receptacle was mated to a
plug and proper latch engagement was confirmed. Testing was terminated after 50 cycles since
no latch integrity failures were observed and this surpassed the 30 mating cycle rating for these
products by 67%.
ECR/ECN INFORMATION:
EC No:
DATE:
08/12/10
TEST SUMMARY
TITLE:
CREATED / REVISED BY:
SSOUSEK
MICRO-FIT (3.0) CONNECTOR SERIES
NYLON 6 RECEPTACLES AND PLUGS
TEST SUMMARY
CHECKED BY:
JBELL
TEMPLATE FILENAME: TEST_SUMMARY[SIZE_A](V.1).DOC
APPROVED BY:
FSMITH
SHEET No.
2
of
3