RF650-868 RF Solutions, RF650-868 Datasheet
RF650-868
Specifications of RF650-868
Related parts for RF650-868
RF650-868 Summary of contents
Page 1
... Because of their small size and low power requirements, both modules are ideal for use in portable, battery- powered applications such as hand-held terminals. Part Numbering Part Number RF650 RF650-868 RF650-EVAL DS650-6 June ‘06 ©2006 RF Solutions Ltd, www.rfsolutions.co.uk Tel 01273 898000 Fax 01273 480661 ...
Page 2
... Page 2 RF650 . . . . . . . . . . . . . . . . . . . . . . ...
Page 3
... Take low when the host is ready to send data to the module or is ready to receive data from the module. Logic ‘0’ is Clear To Send. Out Taken high when the module is busy. Baud Rate 4,800 9,600 19,200 38,400 RF650 16 CTS 15 RTS 14 Config 13 DR2 12 DR1 ...
Page 4
... Operation The Host Data Rate pins are read when the PD pin goes high. The RF650 must be put into standby mode by taking the PD pin low in order to change the selection. The size of RF data packets are set during configuration. If fewer bytes are received by the RF650 than the preset size, then after 10ms from the last byte received from the host, the RF packet will be processed (expanded to meet the preset packet size) and transmitted ...
Page 5
... MHz working frequency: Config value (decimal) = [(desired RF frequency / 2) - 422.4MHz Please Note, the calculated value must be converted into hexadecimal format. The Configuration pin must be held low for at least the first byte to change the RF650 module into configuration mode. If the Configuration pin is still low at the end of the configuration then the module will send the current configuration back to the host ...
Page 6
... The software files are available from the download section of the I. Download and install Labview RunTime Version 6.0. II. Download the ‘RF650_Config’ Zip file and extract the executable to a local file on your PC. III. Set the configuration Pin of the RF650 module to Low. IV. ...
Page 7
... Application Information Connection of the RF650 to an RS232 host terminal device such serial port may easily be achieved using the circuit as below. The 9 way ‘D’ socket (J1) provides the standard pinout required to connect directly to the serial port of any std PC using a 9 way male/female cable. The MAX3232 (U2, a low voltage RS232 line driver) provides level conversion between the RS232 levels on the serial port and the logic levels pins of the that direct connection of RS232 levels to the module will result in immediate destruction of the device) ...
Page 8
... Ohm coaxial cable and the PCB track layout tips given above should be observed. Helical Antenna RF 34mm @ 433MHz 17 turns equally spaced ∅ = 5mm (inside) DS650-6 June ‘06 ©2006 RF Solutions Ltd, www.rfsolutions.co.uk Tel 01273 898000 Fax 01273 480661 MART ADIO RANSCEIVER Whip Antenna RF 15.5cm @ 433MHz RF650 Page 8 ...
Page 9
... RF Solutions Ltd, www.rfsolutions.co.uk Tel 01273 898000 Fax 01273 480661 MART ADIO RANSCEIVER Min. Typ. 1.9 3.3 11 12.5 125 Vcc–0.3 Vcc+0.3V 0 430.0 860 -100 +10 +/- 50 100 -20 - RF650 Max. Units Notes 3 0.3 V 440.0 MHz 2 880.0 MHz 2 dBm dBm kHz kbps +80 Deg C +100 Deg ...
Page 10
... The RF650 evaluation board provides a reliable proven host board for development with the RF650 module. A single board is supplied, no RF650 module is included with the board and the antenna socket is not fitted. This enables the board to be used for either the 433MHz or 868MHz module with a range of antenna socket types ...
Page 11
... OFF : Configuration mode Operating mode. In OFF, OFF : RTS,CTS Disabled ( ON RTS,CTS Enabled ( Out Baud Rate 4,800 9,600 19,200 38,400 RF Solutions Ltd., Unit 21 Cliffe Industrial Estate, South Street, Lewes, E Sussex, BN8 6JL. England http://www.rfsolutions.co.uk RF650 RANSCEIVER Description RS232 without handshake) RS232 with handshake) Page ...