FLUKE-123/003S Fluke, FLUKE-123/003S Datasheet - Page 3
![SCOPE METER, 20MHZ, 2 CHANNEL, 25MSPS](/photos/23/50/235025/3752069_sml.jpg)
FLUKE-123/003S
Manufacturer Part Number
FLUKE-123/003S
Description
SCOPE METER, 20MHZ, 2 CHANNEL, 25MSPS
Manufacturer
Fluke
Type
Digitalr
Specifications of FLUKE-123/003S
Scope Type
Hand Held
Scope Channels
2
Bandwidth
20MHz
Meter Display Type
LCD Monochrome
Sampling Rate
25MSPS
Input Impedance
1Mohm
Rise Time
17.5ns
Input Voltage
1kV
Brand/series
ScopeMeter®/120 Series
Configuration
Handheld
Dimensions
232 mm x 115 mm x 50 mm
Display Type
Monochrome LCD
Interface
RS-232
Memory
512 pts
Number Of Channels
2
Sample Rate
0.025 GS/s
Voltage Range
600 V
10
1 Voltage Probe Included with Fluke 124 for Reduced Circuit Loading
Lead Free Status / RoHS Status
na
Lead Free Status / RoHS Status
na
Cursor measurements
Source: Input A, input B or the mathematical result
trace (excluding A vs B curve)
Dual horizontal lines: Voltage at cursor 1 and 2,
voltage between cursors
Dual vertical lines: Time between cursors, 1/T
between cursors (in Hz), voltage between markers,
risetime with markers, falltime with markers; Vrms
between cursors (190C only), watts between cursors
(190C only)
Single vertical line: Min-Max and Average voltage
at cursor position; frequency and rms-value of individ-
ual frequency component in FFT result (190C only)
Zoom
Up to 16x horizontal zoom
Recorder mode
ScopeRecord – roll mode
Dual input waveform storage mode
Source and display: Input A, input B, dual
Memory depth: 27,500 points per input. Each point
consists of Min-Max pair
Min-Max values: Min-Max values are measured at
high sample rates ensuring capture and display of
glitches
Recording modes: Single sweep, continuous roll,
Start-on-Trigger, Stop-on-Trigger
Stop-on-Trigger (through external): ScopeRecord
mode can be stopped by an individual trigger event, or
by an interruption of a repetitive trigger signal
Horizontal scale: Time from start, time of day
Zoom: Up to 100x
Memory: Up to 2 dual input ScopeRecord waveforms
can be saved for later recall and analysis
TrendPlot
Single or dual input electronic paperless chart
recorder. Plots, displays and stores meter and scope
measurements.
Source and display: Input A, input B or DMM input
Memory depth: 18,000 points recording. Per record
point a minimum, a maximum and an average value,
plus a date and timestamp are recorded.
Ranges: 5 s/div to 30 min/div in normal view mode;
5 min/div to 48 hr/div in view all mode, giving
overview of total record
Recorded timespan: Up to 22 days with a resolution
of 1 minute
Recording mode: Continuous roll for the duration of
the full recordable timespan
Measurement speed: 5 measurements per second
Horizontal scale: Time from start, time of day
Zoom: Up to 64x zoom
Memory: Up to 2 TrendPlot recordings can be saved
for later recall and analysis
Cursor measurements – all recorder modes
Source: Input A, B or DMM input
Dual vertical lines: Min-Max or Average
voltage. Time between cursors
Single vertical line: Min-Max or Average
voltage. Absolute date and time or time from start
Time base range
Recorded timespan
Glitch capture
Sample rate
Resolution
™
recording
5 ms/div to 1 min/div
200 µsec to 2 sec
6 sec to 24 hr
20 MS/s
50 ns
2 min/div
250 ns
4 MS/s
4.8 sec
48 hr
ScopeMeter 190C/190B Series, 120 Series and the NEW ScopeMeter 125
Meter mode
Via 4 mm banana inputs. Fully isolated from scope
inputs and scope ground. The specified accuracy is
valid over the temperature range 18 °C to 28 °C
(65 °F to 82 °F). Add 10 % of specified accuracy for
each degree C below 18 °C or above 28 °C.
Maximum resolution: 5,000 counts
Voltmeter ranges: 500 mV, 5 V, 50 V, 500 V,
1,000 V
Accuracy:
Ohms:
Other meter functions
Continuity: Beeper on < 50 W (± 30 W)
Diode test: Up to 2.8 V
Amps: Adc, Aac, Aac+dc using an optional current
clamp or shunt. Scaling factors: 0.1 mV/A ... 100 V/A
Temperature (°C, °F): With optional accessories. Scale
factors 1 mV/°C or 1 mV/°F
Input impedance: 1 MW ± 1 % // 10 pF ± 2 pF
Advanced meter functions: Auto/manual ranging,
relative measurements (zero reference), TrendPlot
recording
General specifications
Memory save and recall
Scope memories: 10 memory locations that each can
contain two waveforms plus corresponding setup
Recorder memories: 2 memory locations that each
can contain 100 captured dual input scope screens,
or a dual input ScopeRecord (27,500 Min-Max pairs
per input), or a dual input Trendplot (18,000 min-max
pairs + average values)
Real-time clock
Time and date stamp for ScopeRecord, 100 captured
screens and TrendPlots
Mechanical data
Size: 256 x 169 x 64 mm (10.1 x 6.6 x 2.5 in)
Weight: 2 kg (4.4 lbs)
Case
Design: Rugged, shock proof with integrated
protective holster
Drip and dust proof: IP51 according to IEC529
Shock and vibration: Shock 30 g, vibration
(sinusoidal) 3 g according to MIL-PRF-28800F Class 2
Display size: 115.2 mm x 86.4 mm (4.54 in x 3.4 in)
Resolution: 320 x 240 pixels
Contrast and brightness: User adjustable,
temperature compensated
Display
Brightness
Vdc ± (0.5 % + 5 counts)
Vac true rms
Vac+dc true rms
Ranges: 500 W, 5 kW, 50 kW, 500 kW, 5 MW, 30 MW
Accuracy: ± (0.6 % + 5 counts)
15 Hz to 60 Hz: ± (1 % + 10 counts)
60 Hz to 1 kHz: ± (2.5 % + 15 counts)
dc to 60 Hz: ± (1 % + 10 counts)
60 Hz to 1 kHz: ± (2.5 % + 15 counts)
using power adapter
Bright full-color LCD
with backlight,
80 Cd/m
Fluke 190C
2
typ.
using power adapter
125 Cd/m
with backlight
Fluke 190B
Bright LCD
2
typ.
Fluke Corporation 3