D034 ETERNA, D034 Datasheet - Page 2

• Manufacturer Part Number: D034
• Description: TRANSFORMER, 12V, 105VA, 5WAY
• Manufacturer: ETERNA

Specifications of D034

• Transformer Type: Isolation
• Input Voltage: 240V
• Output Voltage: 11.6V
• Current Rating: 460mA
• Power Rating: 105VA
• Svhc: No SVHC (15-Dec-2010)
• Ac Power: 105VA
• Primary Voltages: 240V
• Secondary Current: RoHS Compliant

Read this first:
>
>
>
>
>
>
>
>
>
Live - Brown or Red
Neutral - Blue or Black
Additional red wires may be present in your ceiling
>
Safety markings:
If in any doubt, consult a qualified
electrician.
Suitable for indoor use only.
This product is only suitable for use in living
areas ( not for areas constantly subject to
moisture ).
This product is suitable for installation on
surfaces with normal flammability ( indicated
by the "F" in a triangle )
plasterboard, masonry. It is not suitable for
use on highly flammable surfaces ( e.g.
polystyrene, textiles ).
Do not overload the transformer, check that
the total Wattage of all fittings does not exceed
the maximum marked on the transformer.
If the location of your new transformer requires
the provision of a new electrical supply, the
supply must conform with the requirements of
the latest edition of the IEE wiring regulations.
Do not cover the transformer with any
insulating materials.
Switch off the mains before commencing
installation and remove the appropriate circuit
fuse.
Make connections to the electrical supply in
accordance with the following code:
that are connected to the ring live circuit.
not connect your transformer to these wires. If
these wires are not terminated in a ceiling
terminal block ( not supplied ), ensure that
there are no strands of wire protruding from
the terminals and wrap well with insulating
tape.
This product is designed for permanent
connection to fixed wiring: this should be either
a suitable lighting circuit ( protected with a 5 or
6 Amp MCB or fuse ) or a fused spur ( with a 3
rose, join them together in a separate
115°C
e.g. wood,
D o
>
>
>
>
>
>
>
>
>
>
>
>
>
Amp fuse ) via a fused connection unit. We
recommend that the supply incorporates a
switch for ease of operation.
This transformer is double insulated, do not
connect any part to earth.
Do not connect to a circuit which also has
inductive loads connected as spikes generated
switching inductive loads may damage
electronic components within your transformer.
Ensure that the transformer will be accessible
after
replacement.
The transformer should be placed where it
cannot be splashed.
Do not install on surfaces which are damp,
freshly painted or otherwise electrically
conductive (e.g. metallic surfaces).
The transformer should be installed in a
ventilated area free from sources of heat.
Important ! Disconnect from mains before
High Voltage testing. Do not flash test this
product.
This electronic transformer will shut off the
load automatically in the case of short circuit
and overload. After removing the cause of the
short circuit or overload, the Low Voltage
supply will be restored.
In the event that the transformer overheats, the
low voltage supply will be cut off by the
operation of a thermal fuse to prevent further
damage. The thermal fuse will be reset once
the transformer has cooled down.
It is recommended that this product be used
with Low Voltage compatible dimmers such
as:- Varilight Intelligent, Home Automation Low
Voltage and MK Intelligent Dimmer Switch.
Always allow good ventilation around fitting
and transformer.
When installing intumescent downlight covers,
do not place the transformer inside the fire
hood.
If in any doubt, consult a qualified
electrician.
installation
For use with SELV
( Safety Extra Low
Voltage ) light fittings
for
maintenance
or
Transformer ratings
Primary Voltage ( Mains in )
Primary running current
Low Voltage ( Secondary )
Low Voltage (VA) (Sec)
Max. Sec Amps
Isolation Class
IP Rating
Thermal
Dimmable
Typical installation:
>
>
>
>
>
Choose the location for your transformer. Note
the conditions listed opposite.
Switch off the power at the mains and remove
the appropriate circuit fuse.
We recommend the use of Eterna Lighting Low
Voltage light fittings with this transformer.
Eterna lighting fittings have plugs fitted that are
designed to plug directly into the socket block
fitted to this transformer.
Connect this transformer to the mains using
either ( D033 ) an Eterna ® Link&Light mains
lead ( not supplied ) or ( D034 ) by connecting
directly to your lighting circuit—see opposite.
If you are using a terminal block ( either D033
Mains
Always ensure
that cables are
kept away
from heat
LV
300mm dia. Minimum clear area around fitting
Typical installation
VOID
>
>
Typical LV
Downlighter.
20, 35 or 50W
Dichroic
with Eterna ® Link&Light mains lead or D034
with fitted mains lead ), ensure that
connections are made according to the colour
code opposite. Ensure also that there are no
strands of wire protruding from the terminal
block after making your connections block and
wrap it well with insulating tape.
Connect your low voltage light fittings
Restore the power and switch on.
240Volts 50Hz AC
0.46 Amps
11.6 Volts AC
35—105 VA
8.8 Amps
Class III SELV
IP20
115°C Cut-off, resettable.
Yes