8890 3M, 8890 Datasheet - Page 60
![Static Dissipative Rubber Table Runner](/photos/24/2/240280/4233424_sml.jpg)
8890
Manufacturer Part Number
8890
Description
Static Dissipative Rubber Table Runner
Manufacturer
3M
Datasheet
1.8224.pdf
(138 pages)
Specifications of 8890
Ground Terminals
Stud
External Width
4ft
Thickness
1.7mm
Roll Length
40ft
Color
Gray
Lead Free Status / RoHS Status
na
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
889061
Manufacturer:
TE Connectivity AMP Connectors
Quantity:
12 000
Company:
Part Number:
889062
Manufacturer:
TE Connectivity AMP Connectors
Quantity:
12 000
3M
Image
™
Workstation Products Selection Guide
Product No.
3047
3048
LPCGC151M
LPCGC150M
3050
3051
3057
SP3010
SNAPTOOL
SNAPSOCKET3/8
SNAPSTUD3/8
FPSNAP
Description
Common Point Grounding System, 10 ft. (3 m) to ground workstation components.
Single-row, six-terminal strip, protective cover, three cable clips. Ground cord has a
1 megohm resistor.
Grounding System for 3M
(10 mm snap); grounds two single conductor wrist straps. Comes complete with ring
connector and 15 ft. (4.6 m) ground cord. Ground cord has a 1 megohm resistor for mat
connection only.
This low profile common point ground cord is less obtrusive in the work area. The
system connects two wrist straps and a work surface to ground. Holes are provided for
permanent mounting to a bench. Available with either a 3/8 in. (10 mm) stud or socket
that securely snaps the cord to the mat. A ring terminal connects the opposite end of
the 15 ft. (4.6 m) cord to ground.
Snap Fastener, female, 10 mm diameter. For 3M
8200 Series.
Ground Cord with center snap for standard field service kits. Wrist strap cord section
10 ft. (3.0 m) and ground cord section 5 ft. (1.5 m). Each contains a 1 megohm resistor.
Monitor Stand-By Jack. Allows operator to disconnect a ground cord from the wrist
band and leave the workstation without deactivating the 3M
Monitor 724 or 3M
Soldering Tool. 3M’s SP3010 Soldering Tool will help you form component leads, probe
circuit cards, and chase wire and leads. Tough glass-filled nylon plastic makes this tool
durable and long lasting.
This simple-to-use tool attaches snaps to static mats. Three easy steps give you a
secure snap with good electrical connection. Rugged and rust resistant, the snap tool
allows you to put a grounding snap right where you need it.
Socket snaps are held in place by crimping the tip of an eyelet through the center of
the socket with a snap tool. This traps the mat between the socket on the top of the
mat and the eyelet on the back of the mat. 10 sockets and eyelets are included in each
pack. Use with SNAPTOOL.
Stud snaps are held in place by crimping the tip of an eyelet through the center of the stud
with a snap tool. This traps the mat between the stud on the top of the mat and the eyelet on
the back of the mat. 10 studs and eyelets are included in each pack. Use with SNAPTOOL.
Prong clinch snaps are held in place by putting the prongs through the mat and crimping
them on the bottom of the mat. No special tools are needed.
Workstation Products
™
Static Monitor 790.
™
Wrist Strap/Table Mat. Easily snaps onto mats and runners,
™
Table and Floor Mats and Runners
™
Wrist Strap Workstation
55