082-0068 MULTICOMP, 082-0068 Datasheet - Page 2

• Manufacturer Part Number: 082-0068
• Description: ESD ANTISLIP CUT MAT, BLUE, 600X1200
• Manufacturer: MULTICOMP

Specifications of 082-0068

• Mat Type: Floor
• Mat Material: Rubber
• Length: 1200mm
• External Width: 600mm
• Thickness: 4mm
• Mat Features: Dissipative
• Colour: Blue / Black
• Lead Free Status / RoHS Status: na

ESD Anti Slip Multipurpose Matting
GROUNDING:
Sufficient ground cords should be used to reliably meet EN 61340-5-1 Table 3 less than 1 x 10
Industry recommendation is that continuous runs of ESD matting should be grounded at 10ft intervals to allow proper charge
decay rates. Each individual ESD mat should be grounded with ground snaps located no further than five feet from either
end.
CLEANING:
Please note that contact between the matting surface and any acid or alkali solvent is strictly prohibited (such as Benzene,
Alcohol etc), this will result in the antistatic performance wearing away. If cleaning is required, the matting may be wiped with
a cloth coated in a neutral solution (such as water).
GUIDANCE ON USE:
Matting materials have a tendency to shrink slightly when first unrolled. In applications where length is critical, allow the
material to relax for at least 4 hours before cutting to size. Matting should always be trimmed with a sharp knife or razor blade.
CUTTING TOLERANCES:
Width + 6mm
Length + 6mm every linear foot of running material
RoHS COMPLIANCE:
None of the following materials are intentionally added in manufacturing this product: lead, mercury, cadmium, hexavalent
chromium, polybrominated biphenyls (PBB) or polybrominated diphenyl ethers (PBDE) as outlined in the Directive 2002/95/
EC Article 4.1.
R
mat. A proper R
ESD STM-4.1 for R
R
resistance properties. The ESD STM-4.1 guideline for R
Test Results:
Surface Resistance / R
Bottom Resistance / R
Volume Resistance
Thickness
Temperature Resistance
Temperature
Relative Humidity
Disclaimer
in connection with the products to which it relates. No licence of any intellectual pr o perty rights is granted. The Information is subject to change without notice and replaces all data sheets previousl y supplied.
The Information supplied is believed to be accurate but the Group assumes no responsibility for its accuracy or completeness, a ny error in or omission from it or for any use made of it. Users of this data
sheet should check for themselves the Information and the suitability of the products for their purpose and not make any assump tions based on information included or omitted. Liability for loss or damage
resulting from any r eliance o n the Information or use o f it ( including liability r esulting from negligence o r where the Group w as a ware o f the possibility of such l oss o r damage a rising) i s excluded.
This will not operate to limit or restrict the Group's liability for death or personal injury resulting from its negligence. SPC Multicomp is the registered trademark of the Group. © Premier Farnell plc 2008.
TG
TT
http://www.farnell.com
http://www.newark.com
http://www.cpc.co.uk
is the resistance from one point on the mat’s surface to another point. A proper R
is the resistance from one point on the mat’s surface to the mat’s ground point, and is the fundamental electrical test for a
This data sheet and its contents (the "Information") belong to the Premier Farnell Group (the "Group") or are licensed to it. No licence is granted for the use of it other than for information purposes
TG
insures that a mat can conduct charge from a point on the surface to the mat ground point. The guideline in
TG
is 1x10
TG
TT
6
to 1x10
9
ohms. ANSI/ESD S-20.20 has an upper limit of <1 x10
Test Method:
SJ/T10694-2004
SJ/T10694-2004
GB/T14437-97
YY-1001
YY-1001
N/A
N/A
TT
is >1x10
P
a
g
e
6
<
ohms.
1
>
Unit:
Ω
Ω
Ω
mm
o
o
%
C
C
TT
insures the consistency of the mat’s
9
ohms.
9
ohms for working surfaces.
Value:
1x10
1x10
1x10
Permissable Tolerance +0.1
180 (Instantaneous Temp)
20-26
40-65
6
3
5
< R < 1x10
< R < 1x10
< R < 1x10
9
6
8
2
2
1 /
0
0 /
8
V
1
1 .