LM3429BSTEVAL National Semiconductor, LM3429BSTEVAL Datasheet
![no-image](/images/manufacturer_photos/0/4/469/national_semiconductor_sml.jpg)
LM3429BSTEVAL
Specifications of LM3429BSTEVAL
Available stocks
Related parts for LM3429BSTEVAL
LM3429BSTEVAL Summary of contents
Page 1
... The LM3429 comes in a low profile, thermally efficient TSSOP EP 14-lead package. The LM3429Q1 is an Automotive Grade product that is AEC- Q100 grade 1 qualified Typical Boost Application Circuit © 2010 National Semiconductor Corporation LM3429 LM3429Q1 Features ■ LM3429Q1 is an Automotive Grade product that is AEC- Q100 grade 1 qualified (-40° ...
Page 2
Connection Diagram Ordering Information Order Number Spec. Package Type LM3429MH NOPB TSSOP-14 EP LM3429MHX NOPB TSSOP-14 EP LM3429Q1MH NOPB TSSOP-14 EP LM3429Q1MHX NOPB TSSOP-14 EP *Automotive Grade (Q) product incorporates enhanced manufacturing and support processes for the automotive market, including ...
Page 3
... Absolute Maximum Ratings If Military/Aerospace specified devices are required, please contact the National Semiconductor Sales Office/ Distributors for availability and specifications nDIM IN OVP, HSP, HSN RCT - continuous COMP, CSH GATE - continuous Electrical Characteristics Specifications in standard type face are for T Range ( T = −40°C to +125°C). Minimum and Maximum limits are guaranteed through test, design, or statistical correlation. Typical ...
Page 4
Symbol Parameter PWM COMPARATOR COMP to PWM Offset CURRENT LIMIT (IS) V Current Limit Threshold LIM V Delay to Output LIM t Leading Edge Blanking ON-MIN Time HIGH SIDE TRANSCONDUCTANCE AMPLIFIER Input Bias Current Transconductance Input Offset Current Input Offset ...
Page 5
Typical Performance Characteristics Boost Efficiency vs. Input Voltage V = 32V (9 LEDs) (Note O Boost LED Current vs. Input Voltage (Note V = 32V (9 LEDs) O Analog Dimming (Note V = 20V (6 LEDs =+25°C and ...
Page 6
V vs. Junction Temperature CSH V vs. Junction Temperature RCT t vs. Junction Temperature ON-MIN www.national.com V vs. Junction Temperature CC 300944b0 V vs. Junction Temperature LIM 300944b2 300944b4 6 300944b1 300944b3 ...
Page 7
Block Diagram Theory of Operation The LM3429 is an N-channel MosFET (NFET) controller for buck, boost and buck-boost current regulators which are ideal for driving LED loads. The controller has wide input voltage range allowing for regulation of a variety ...
Page 8
The average output LED current (I LED average inductor current ( therefore trolled, I will be well regulated. As the system changes LED input voltage or output voltage, the ideal duty cycle (D) is var- ...
Page 9
Adding a PNP transistor as shown in constant ripple over varying FIGURE 3. Off-timer Circuitry for Buck Regulators The switching frequency is defined: Buck (Constant Ripple vs Buck (Constant Ripple vs ...
Page 10
ANALOG DIMMING The CSH pin can be used to analog dim the LED current by adjusting the current sense voltage (V different methods to adjust V using the CSH pin: SNS 1. External variable resistance : Adjust a potentiometer placed ...
Page 11
CONTROL LOOP COMPENSATION The LM3429 control loop is modeled like any current mode controller. Using a first order approximation, the uncompen- sated loop can be modeled as a single pole created by the output capacitor and, in the boost and ...
Page 12
To mitigate this problem, a compensator should be designed to give adequate phase margin (above 45°) at the crossover frequency. A simple compensator using a single capacitor at the COMP pin (C ) will add a dominant pole to the ...
Page 13
INPUT UNDER-VOLTAGE LOCKOUT (UVLO) The nDIM pin is a dual-function input that features an accurate 1.24V threshold with programmable hysteresis as shown in Figure 12. This pin functions as both the PWM dimming input for the LEDs and as a ...
Page 14
Design Considerations This section describes the application level considerations when designing with the LM3429. For corresponding calcu- lations, refer to the Design Guide section. INDUCTOR The inductor (L1) is the main energy storage device in a switching regulator. Depending on ...
Page 15
N-CHANNEL MosFET (NFET) The LM3429 requires an external NFET (Q1) as the main power MosFET for the switching regulator recommend have a voltage rating at least 15% higher than the maximum transistor voltage to ensure safe ...
Page 16
Basic Topology Schematics BOOST REGULATOR (V < BUCK REGULATOR (V > www.national.com 16 30094422 30094451 ...
Page 17
BUCK-BOOST REGULATOR 17 30094450 www.national.com ...
Page 18
Design Guide Refer to Basic Topology Schematics section. SPECIFICATIONS Number of series LEDs: N Single LED forward voltage: V LED Single LED dynamic resistance: r LED Nominal input voltage Input voltage range IN-MAX IN-MIN Switching ...
Page 19
LED RIPPLE CURRENT Set the nominal LED ripple current (Δi LED-PP the output capacitance ( Buck Boost and Buck-boost To set the worst case LED ripple current, use D solving for The minimum allowable ...
Page 20
A high frequency compensation pole (ω attenuate switching noise and provide better gain margin. As- = 10Ω, C suming R is calculated according to the higher FS FS value of the pole and the RHP zero of the system (shown ...
Page 21
The current rating should be at least 10% higher than the maximum average diode current (I D-MAX Buck Boost and Buck-boost Replace D with D in the I equation to solve for the MAX D-MAX average diode current (I ). ...
Page 22
Design Example #1 BUCK-BOOST APPLICATION - 6 LEDs at 1A SPECIFICATIONS 3.5V LED r = 325 mΩ LED V = 24V 10V IN-MIN V = 70V IN-MAX f = 700 kHz SW ...
Page 23
AVERAGE LED CURRENT Solve for R : SNS Assume R = 12.4 kΩ and solve for R CSH The closest standard resistor for R is actually 0.1Ω and for SNS R is actually 1 kΩ therefore I is: HSP ...
Page 24
T is approximated ensure stability, calculate ω Solve for C : CMP To attenuate switching noise, calculate ω = 10Ω and solve for C Assume The chosen components from step 7 are: 8. ...
Page 25
The closest standard resistor is 21 kΩ making V The chosen components from step 11 are: 12. OUTPUT OVLO Solve for R : OV2 Design #1 Bill of Materials Qty Part ID 1 LM3429 1 C CMP ...
Page 26
Applications Information DESIGN #2: BOOST PWM DIMMING APPLICATION - 9 LEDs at 1A Design #2 Bill of Materials Qty Part ID 1 LM3429 CMP ...
Page 27
DESIGN #3: BUCK-BOOST ANALOG DIMMING APPLICATION - 4 LEDs at 2A Design #3 Bill of Materials Qty Part ID 1 LM3429 1 C CMP ...
Page 28
DESIGN #4: BOOST ANALOG DIMMING APPLICATION - 12 LEDs at 700mA Design #4 Bill of Materials Qty Part ID 1 LM3429 1 C CMP ...
Page 29
DESIGN #5: BUCK-BOOST PWM DIMMING APPLICATION - 6 LEDs at 500mA Design #5 Bill of Materials Qty Part ID 1 LM3429 1 C CMP ...
Page 30
DESIGN #6: BUCK APPLICATION - 3 LEDS AT 1.25A Design #6 Bill of Materials Qty Part ID 1 LM3429 1 C CMP ...
Page 31
DESIGN #7: BUCK-BOOST THERMAL FOLDBACK APPLICATION - 8 LEDs at 2.5A Design #7 Bill of Materials Qty Part ID 1 LM3429 1 C CMP ...
Page 32
DESIGN #8: SEPIC APPLICATION - 5 LEDs at 750mA Design #8 Bill of Materials Qty Part ID 1 LM3429 1 C CMP ...
Page 33
Physical Dimensions inches (millimeters) unless otherwise noted For Ordering, Refer to Ordering Information Table TSSOP-14 Pin EP Package (MXA) NS Package Number MXA14A 33 www.national.com ...
Page 34
... For more National Semiconductor product information and proven design tools, visit the following Web sites at: www.national.com Products Amplifiers www.national.com/amplifiers Audio www.national.com/audio Clock and Timing www.national.com/timing Data Converters www.national.com/adc Interface www.national.com/interface LVDS www.national.com/lvds Power Management www.national.com/power Switching Regulators www.national.com/switchers LDOs www.national.com/ldo LED Lighting www ...