SC4519HEVB-1 Semtech, SC4519HEVB-1 Datasheet - Page 9
![EVALUATION BOARD](/photos/24/9/240934/4296862_sml.jpg)
SC4519HEVB-1
Manufacturer Part Number
SC4519HEVB-1
Description
EVALUATION BOARD
Manufacturer
Semtech
Datasheet
1.SC4519HSETRT.pdf
(14 pages)
Specifications of SC4519HEVB-1
Silicon Manufacturer
Semtech
Application Sub Type
Step Down Switching Regulator
Kit Application Type
Power Management - Voltage Regulator
Silicon Core Number
SC4519H
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
capacitor must be able to provide the ripple current
drawn by the converter. For the continuous conduction
mode, the RMS value of the input capacitor current
I
This current gives the capacitor’s power loss through its
R
The input ripple voltage mainly depends on the input
capacitor’s ESR and its capacitance for a given load, input
voltage and output voltage. Assuming that the input
current of the converter is constant, the required input
capacitance for a given voltage ripple can be calculated
by:
Where:
Because the input capacitor is exposed to the large surge
current, attention is needed for the input capacitor. If
tantalum capacitors are used at the input side of the
converter, one needs to ensure that the RMS and surge
ratings are not exceeded. For generic tantalum
capacitors, it is suggested to derate their voltage ratings
at a ratio of about two to protect these input capacitors.
Boost Capacitor and its Supply Source Selection
The boost capacitor selection is based on its discharge
ripple voltage, worst case conduction time and boost
current. The worst case conduction time T
estimated as follows:
Where:
f
Dmax = maximum duty ratio, 0.85 for the SC4519H.
The required minimum capacitance for the boost
capacitor will be:
POWER MANAGEMENT
Application Information (Cont.)
CIN(RMS)
s
CIN(ESR)
V
2007 Semtech Corp.
= the switching frequency and
I
= the given input voltage ripple.
can be calculated from:
as follows:
C
IN
I
CIN
I
P
(RMS)
OMAX
CIN
C
I
T
fs
2
boost
I
W
CIN
OMAX
(
(RMS)
f
V
1
s
I
V
I
D
B
D
D
I
V
max
OMAX
(1
R
T
O
W
CIN(ESR)
(V
V
D)
R
I
2
I
CIN
V
O
(ESR)
)
)
w
can be
9
Where:
I
V
With f
minimum capacitance for the boost capacitor is:
The internal driver of the switch requires a minimum 2.7V
to fully turn on that switch to reduce its conduction loss.
If the output voltage is less than 2.7V, the boost capacitor
can be connected to either the input side or an
independent supply with a decoupling capacitor. But the
Pin BST should not see a voltage higher than its maximum
rating.
Freewheeling Diode Selection
This diode conducts during the switch’s off-time. The diode
should have enough current capability for full load and
short circuit conditions without any thermal concerns.
Its maximum repetitive reverse block voltage has to be
higher than the input voltage of the SC4519H. A low
forward conduction drop is also required to increase the
overall efficiency. The freewheeling diode should be
turned on and off fast with minimum reverse recovery
because the SC4519H is designed for high frequency
applications. SS23 Schottky rectifier is recommended
for certain applications. The average current of the diode,
I
Thermal Considerations
There are three major power dissipation sources for the
SC4519H. The internal switch conduction loss, its
switching loss due to the high frequency switching actions
and the base drive boost circuit loss. These losses can
be estimated as:
Where:
I
R
V
connection.
P
B
D
O
D
BOOST
on
_
total
= the boost current and
= discharge ripple voltage.
= load current;
AVG
= on-equivalent resistance of the switch;
= input voltage or output based on the boost circuit
s
can be calculated by:
I
o
= 600kHz, V
C
2
boost
R
on
V
D
I
B
D
10.8
I
f
1
s
D
-
D
AVG
D
= 0.5V and I
max
10
I
omax
3
0.045
0.5
I
o
V
I (
I
600k
B
=0.045A, the required
1
D
1000
10
)
0.85
SC4519H
I
o
www.semtech.com
D
128nF
(V
boost
)