19269 Loctite, 19269 Datasheet

PRIMER, BOTTLE, 1.75FL.OZ

19269

Manufacturer Part Number
19269
Description
PRIMER, BOTTLE, 1.75FL.OZ
Manufacturer
Loctite
Series
7469r
Datasheet

Specifications of 19269

Color
Clear/Green
Dispensing Method
Bottle
Volume
1.75fl.oz. (US)
Pack Quantity
1
Acetone Solvent
RoHS Compliant
Features
Increases Cure Speed Of Loctite Anaerobic Adhesive & Sealant Products
Rohs Compliant
Yes

Available stocks

Company
Part Number
Manufacturer
Quantity
Price
Part Number:
1926945-1
Manufacturer:
INTEL
Quantity:
430
Part Number:
1926945-2
Manufacturer:
TE
Quantity:
20 000
Part Number:
192696-TT95N
Manufacturer:
SANREX
Quantity:
452
Part Number:
192697-TT104N
Manufacturer:
SEMIKRON
Quantity:
492
PRODUCT DESCRIPTION
LOCTITE
characteristics:
LOCTITE
LOCTITE
recommended for applications with passive metals or inert
surfaces and with large bond gaps. LOCTITE
particularly recommended when prevailing temperature is low
(<15 °C).
NSF International
Certified to ANSI/NSF Standard 61 for use in commercial and
residential potable water systems not exceeding 82° C. Note:
This is a regional approval. Please contact your local Technical
Service Center for more information and clarification.
NSF International
Registered to NSF Category P1 for use as a sealant where
there is no possibilty of food contact in and around food
processing areas. Note: This is a regional approval. Please
contact your local Technical Service Center for more
information and clarification.
TYPICAL PROPERTIES
TYPICAL PERFORMANCE
Fixture time and cure speed achieved as a result of using
LOCTITE
substrate bonded.
(Fixture time is defined as the time to develop a shear strength
of 0.1 N/mm²)
Technology
Chemical Type
Solvent
Appearance
Viscosity
Cure
Application
Specific Gravity @ 25 °C
Viscosity @ 20 °C, mPa·s (cP)
Flash Point - See MSDS
Drying Time @ 20 °C, seconds
On Part Life, days
Fixture Time, ISO 4587, seconds:
Steel (degreased) using LOCTITE
, single side activation
®
®
®
®
anaerobic products is required. It is especially
7649™ is used where increased cure speed of
7649™ depend on the adhesive used and the
7649™
provides
Activator for LOCTITE
adhesives and sealants
Copper salt and Aliphatic amine
Acetone
Transparent, green liquid
Very low
Not applicable
Cure acceleration of
LOCTITE
®
®
326™,
anaerobic products
the
following
®
anaerobic
®
LMS
7649™ is
0.79
2
30 to 70
≤30
≤30
product
Handling precautions
Activator must be handled in a manner applicable to highly
flammable materials and in compliance with relevant local
regulations.
The solvent can affect certain plastics or coatings. It is
recommended to check all surfaces for compatibility before
use.
GENERAL INFORMATION
This product is not recommended for use in pure oxygen
and/or oxygen rich systems and should not be selected
with a sealant for chlorine or other strong oxidizing
materials.
For safe handling information on this product, consult the
Material Safety Data Sheet (MSDS).
Under no circumstances should activator and adhesive be
mixed directly as liquids.
Use only in a well ventilated area
Where aqueous washing systems are used to clean the
surfaces before bonding, it is important to check for
compatibility of the washing solution with the adhesive. In
some cases these aqueous washes can affect the cure and
performance of the adhesive.
Directions for use:
1. Spray or brush on the activator on both mating surfaces to
2. Allow the solvent time to evaporate under good ventilation
3. After activation, parts should be bonded within
4. Apply the Loctite Anaerobic product to one or both
5. Where possible, move surfaces in relation to each other
6. Secure the assembly and await fixturing before any
be bonded. For small gaps, treatment of only one surface
may be adequate. Contaminated surfaces may need
repeated treatment or special degreasing prior to
activation to remove any dissolvable contamination.
Porous surfaces may need two treatments of activator.
until the surfaces are completely dry.
Contamination of the surface before bonding should be
prevented.
surfaces and assemble parts immediately.
for a few seconds on assembly to properly distribute the
adhesive and for maximum activation..
further handling..
LOCTITE
®
Technical Data Sheet
7649™
December-2009
1-
month.

19269 Summary of contents

Page 1

... After activation, parts should be bonded within Contamination of the surface before bonding should be prevented. 4. Apply the Loctite Anaerobic product to one or both surfaces and assemble parts immediately. 5. Where possible, move surfaces in relation to each other for a few seconds on assembly to properly distribute the adhesive and for maximum activation.. ...

Page 2

... Loctite Material Specification LMS LMS dated September-01, 1995. Test reports for each batch are available for the indicated properties. LMS test reports include selected QC test parameters considered appropriate to specifications for customer use. Additionally, comprehensive controls are in place to assure product quality and consistency ...