29031 Loctite, 29031 Datasheet - Page 3

• Manufacturer Part Number: 29031
• Description: ACRYLIC ADHESIVE, BOTTLE, 50ML
• Manufacturer: Loctite
• Series: 290r

Specifications of 29031

• Adhesive Type: Acrylic
• Color: Green
• Dispensing Method: Bottle
• Volume: 50ml
• Pack Quantity: 1
• Mil Spec: MIL-S-46163A For Existing Designs, ASTM D-5363, NSF/ANSI 61, NSF P1, CFIA
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

Chemical/Solvent Resistance
Aged under conditions indicated and tested @ 22 °C.
GENERAL INFORMATION
This product is not recommended for use in pure oxygen
and/or oxygen rich systems and should not be selected as
a sealant for chlorine or other strong oxidizing materials
For safe handling information on this product, consult the
Material Safety Data Sheet (MSDS).
Where aqueous washing systems are used to clean the
surfaces before bonding, it is important to check for
compatibility of the washing solution with the adhesive. In
some cases these aqueous washes can affect the cure and
performance of the adhesive.
This product is not normally recommended for use on plastics
(particularly thermoplastic materials where stress cracking of
the plastic could result). Users are recommended to confirm
compatibility of the product with such substrates.
Directions for use:
Henkel Americas
+860.571.5100
Environment
Motor oil (MIL-L-46152)
Leaded Petrol
Brake fluid
Water/glycol 50/50
Acetone
Ethanol
For Pre-assembled Threaded Parts with Thru Holes
For Assembly
For Porosity Sealing
For Disassembly
For Cleanup
1. Prior to assembly, clean all threads (bolt and hole) with a
2. For Thru Holes, apply several drops of product at screw
3. Avoid touching the bottle tip to the metal surface.
1. For Blind Holes, apply several drops of the product
1. Clean area and apply localized heat to the area to
2. Allow to cool to approximately 85°C and apply the
1. Remove with standard hand tools.
2. In rare instances where hand tools do not work because
1. Cured product can be removed with a combination of
LOCTITE
and body juncture.
down the internal threads to the bottom of the hole
approximately 121°C.
product.
of excessive engagement length, apply localized heat to
nut or bolt to approximately 250 °C. Disassemble while
hot.
soaking
abrasion such as a wire brush.
For the most direct access to local sales and technical support visit: www.henkel.com/industrial
®
in a
cleaning solvent and allow to dry.
125
LOCTITE
°C
22
22
87
22
22
100 h
85
90
90
90
85
80
®
solvent
% of initial strength
500 h
85
90
90
90
85
80
and
1000 h
50
90
85
90
85
80
mechanical
+49.89.320800.1800
5000 h
50
90
85
90
85
80
Henkel Europe
Loctite Material Specification
LMS dated September-01, 1995. Test reports for each batch
are available for the indicated properties. LMS test reports
include selected QC test parameters considered appropriate to
specifications for customer use. Additionally, comprehensive
controls are in place to assure product quality and
consistency. Special customer specification requirements may
be coordinated through Henkel Quality.
Storage
Store product in the unopened container in a dry location.
Storage information may be indicated on the product container
labeling.
Optimal Storage: 8 °C to 21 °C. Storage below 8 °C or
greater than 28 °C can adversely affect product properties.
Material removed from containers may be contaminated during
use. Do not return product to the original container. Henkel
Corporation cannot assume responsibility for product which
has been contaminated or stored under conditions other than
those previously indicated. If additional information is required,
please contact your local Technical Service Center or
Customer Service Representative.
Conversions
(°C x 1.8) + 32 = °F
kV/mm x 25.4 = V/mil
mm / 25.4 = inches
µm / 25.4 = mil
N x 0.225 = lb
N/mm x 5.71 = lb/in
N/mm² x 145 = psi
MPa x 145 = psi
N·m x 8.851 = lb·in
N·m x 0.738 = lb·ft
N·mm x 0.142 = oz·in
mPa·s = cP
Note
The data contained herein are furnished for information only
and are believed to be reliable.
responsibility for the results obtained by others over whose
methods we have no control. It is the user's responsibility to
determine suitability for the user's purpose of any production
methods mentioned herein and to adopt such precautions as
may be advisable for the protection of property and of persons
against any hazards that may be involved in the handling and
use thereof. In light of the foregoing, Henkel Corporation
specifically disclaims all warranties expressed or implied,
including warranties of merchantability or fitness for a
particular purpose, arising from sale or use of Henkel
Corporation’s products. Henkel Corporation specifically
disclaims any liability for consequential or incidental
damages of any kind, including lost profits. The discussion
herein of various processes or compositions is not to be
interpreted as representation that they are free from
domination of patents owned by others or as a license under
any Henkel Corporation patents that may cover such
processes or compositions.
prospective user test his proposed application before repetitive
use, using this data as a guide. This product may be covered
by one or more United States or foreign patents or patent
applications.
TDS LOCTITE
LMS
We recommend that each
®
We cannot assume
290™, January-2010
Henkel Asia Pacific
+86.21.2891.8863