29513 Loctite, 29513 Datasheet - Page 2

• Manufacturer Part Number: 29513
• Description: ACRYLIC ADHESIVE, BOTTLE, 10ML
• Manufacturer: Loctite
• Series: 246r

Specifications of 29513

• Adhesive Type: Acrylic
• Color: Blue
• Dispensing Method: Bottle
• Volume: 10ml

TYPICAL ENVIRONMENTAL RESISTANCE
Hot Strength
Tested at temperature
Heat Aging
Aged at temperature indicated and tested @ 22 °C
Henkel Americas
+860.571.5100
After 24 hours @ 22 °C followed by 72 hours @ 204 °C, tested @ 22
°C
After 24 hours @ 22 °C
Lubricity, K-Factor:
Breakaway Torque, ISO 10964:
Prevail Torque, ISO 10964:
Breakloose Torque, ISO 10964, Pre-torqued to 5 N·m:
3/8 x 16 phosphate & oil bolts and
steel nuts
3/8 x 16 steel nuts (grade
2) and bolts (grade 5)
3/8 x 16 steel nuts (grade
2) and bolts (grade 5)
M10 zinc phosphate steel nuts and bolts
100
200
175
150
125
100
75
50
25
75
50
25
0
0
For the most direct access to local sales and technical support visit: www.henkel.com/industrial
0
0
100 200 300 400 500 600 700 800 900 1000
260 °C
50
100
Reoiled
Degreased
150
N·m
(lb.in.)
N·m
(lb.in.)
200
(50)
(18)
0.17
≥5.7
≥2.0
LMS
LMS
250
+49.89.320800.1800
Henkel Europe
300
Chemical/Solvent Resistance
Aged under conditions indicated and tested @ 22 °C.
GENERAL INFORMATION
This product is not recommended for use in pure oxygen
and/or oxygen rich systems and should not be selected as
a sealant for chlorine or other strong oxidizing materials
For safe handling information on this product, consult the
Material Safety Data Sheet (MSDS).
Where aqueous washing systems are used to clean the
surfaces before bonding, it is important to check for
compatibility of the washing solution with the adhesive. In
some cases these aqueous washes can affect the cure and
performance of the adhesive.
This product is not normally recommended for use on plastics
(particularly thermoplastic materials where stress cracking of
the plastic could result). Users are recommended to confirm
compatibility of the product with such substrates.
Directions for use:
For Assembly
For Disassembly
Environment
Motor oil (MIL-L-46152)
Unleaded gasoline
Brake fluid
Ethanol
Acetone
Water/glycol 50/50
Transmission fluid
1. For best results, clean all surfaces (external and internal)
2. If the material is an inactive metal or the cure speed is too
3. Shake the product thoroughly before use.
4. To prevent the product from clogging in the nozzle, do not
5. For Thru Holes, apply several drops of the product onto
6. For Blind Holes, apply several drops of the product down
7. For Sealing Applications, apply a 360° bead of product
8. Assemble and tighten as required.
1. Remove with standard hand tools.
2. In rare instances where hand tools do not work because
with a LOCTITE
slow, spray all threads with Activator 7471™ or 7649™
allow the tip to touch metal surfaces during application.
the bolt at the nut engagement area.
the internal threads to the bottom of the hole.
to the leading threads of the male fitting, leaving the first
thread free. Force the material into the threads to
thouroughly fill the voids. For bigger threads and voids,
adjust product amount accordingly and apply a 360° bead
of product on the female threads also.
of excessive engagement length, apply localized heat to
nut or bolt to approximately 250 °C. Disassemble while
hot.
and allow to dry.
®
cleaning solvent and allow to dry.
125
125
°C
22
22
22
22
87
TDS LOCTITE
100 h
180
100
150
175
95
90
75
% of initial strength
®
246™, January-2011
500 h
Henkel Asia Pacific
180
110
165
175
95
95
75
+86.21.2891.8863
1000 h
180
120
100
165
185
95
75