0103114 Loctite, 0103114 Datasheet - Page 2

• Manufacturer Part Number: 0103114
• Description: SCREWLOCK, 10ML
• Manufacturer: Loctite
• Series: 222r

Specifications of 0103114

• Adhesive Type: Anaerobic
• Adhesive Applications: Thread Locking
• Colour: Pink
• Svhc: No SVHC (15-Dec-2010)
• Breakaway Torque Max: 11N-m
• Breakaway Torque Min: 3N-m
• Cure Time Max: 2h
• Dispensing Method: Bottle
• Gap: RoHS Compliant
• Volume: 10ml
• Rohs Compliant: Yes

Breakaway Torque, ISO 10964, N.m
Prevail Torque, ISO 10964, N.m
Breakloose Torque, DIN 54454, N.m
Max. Prevail Torque, DIN 54454, N.m
Test Procedure :
Substrate:
Cure procedure:
PERFORMANCE OF CURED MATERIAL
(After 24 hr at 22 C on M10 steel nuts & bolts)
TYPICAL ENVIRONMENTAL RESISTANCE
Hot Strength
Tested at temperature.
Heat Aging
Aged at temperature indicated and tested at 22°C.
Chemical / Solvent Resistance
Aged under conditions indicated and tested at 22°C.
Motor Oil
Leaded Petrol
Brake Fluid
Water/Glycol
(50%/50%)
Ethanol
Acetone
GENERAL INFORMATION
This product is not recommended for use in pure oxygen
and/or oxygen rich systems and should not be selected as a
sealant for chlorine or other strong oxidising materials.
100
125
100
75
50
25
75
50
25
0
0
0
0
Solvent
1,000
50
Temperature, °C
Temp
125
22 C
22 C
87 C
22 C
22 C
2,000
C
.
(lb.in)
(lb.in)
(lb.in)
(lb.in)
1 week at 22 C
Breakloose Torque, DIN 54454
M10 Zinc Phosphate Nuts & Bolts
Hours
100
hr
100
100
95
95
80
95
3,000
% Initial Strength retained at
100
Value
(120)
(120)
500
(53)
(30)
hr
14
14
6
4
95
95
95
80
95
90
4,000
Typical
1000 hr
120°C
(71 to 180)
(71 to 180)
(25 to 80)
(10 to 50)
150°C
90
95
95
80
90
90
8 to 20
8 to 20
3 to 9
1 to 6
Range
5,000
150
5000 hr
85
95
90
80
90
90
For safe handling information on this product, consult the
Material Safety Data Sheet, (MSDS).
Where aqueous washing systems are used to clean the
surfaces before bonding, it is important to check for compatibility
of the washing solution with the adhesive. In some cases these
aqueous washes can affect the cure and performance of the
adhesive.
This product is not normally recommended for use on plastics
(particularly thermoplastic materials where stress cracking of
the plastic could result). Users are recommended to confirm
compatibility of the product with such substrates.
Directions for use
For best performance surfaces should be clean and free of
grease. Product should be applied to the bolt in sufficient
quantity to fill all engaged threads. This product performs best in
thin bond gaps, (0.05mm). Very large thread sizes may create
large gaps which will affect
product is designed to give controlled friction, (torque/tension
ratio), during assembly. In critical tightening applications this
ratio should be confirmed.
Storage
Product shall be ideally stored in a cool, dry location in
unopened containers at a temperature between 8 C to 28 C
(46 F to 82 F) unless otherwise labelled. Optimal storage is at
the lower half of this temperature range.
contamination of unused product, do not return any material to
its original container. For further specific shelf life information,
contact your local Technical Service Centre.
Data Ranges
The data contained herein may be reported as a typical value
and/or range (based on the mean value 2 standard deviations).
Values are based on actual test data and are verified on a
periodic basis.
Note
The data contained herein are furnished for information only and
are believed to be reliable. We cannot assume responsibility for
the results obtained by others over whose methods we have no
control. It is the user's responsibility to determine suitability for
the user's purpose of any production methods mentioned herein
and to adopt such precautions as may be advisable for the
protection of property and of persons against any hazards that
may be involved in the handling and use thereof. In light of the
foregoing,
warranties expressed or implied, including warranties of
merchantability or fitness for a particular purpose, arising from
sale or use of Loctite Corporation’s products.
Corporation specifically disclaims any liability for consequential
or incidental damages of any kind, including lost profits. The
discussion herein of various processes or compositions is not to
be interpreted as representation that they are free from
domination of patents owned by others or as a license under
any Loctite Corporation patents that may cover such processes
or compositions. We recommend that each prospective user
test his proposed application before repetitive use, using this
data as a guide. This product may be covered by one or more
United States or foreign patents or patent applications.
Loctite is a Registered Trademark of Loctite Corporation, Hartford, CT 06106
Loctite
Corporation
cure speed and strength. This
TDS 222, October 1995
specifically
disclaims
To prevent
Loctite
all