SIM2065-6-0-18-00-A GLOBAL CONNECTOR TECHNOLOGY, SIM2065-6-0-18-00-A Datasheet - Page 2
![MEMORY SOCKET, SIM CARD, 6POS](/photos/24/74/247400/4664959_sml.jpg)
SIM2065-6-0-18-00-A
Manufacturer Part Number
SIM2065-6-0-18-00-A
Description
MEMORY SOCKET, SIM CARD, 6POS
Manufacturer
GLOBAL CONNECTOR TECHNOLOGY
Datasheet
1.SIM2065-6-0-18-00-A.pdf
(2 pages)
Specifications of SIM2065-6-0-18-00-A
Connector Type
SIM Socket
No. Of Contacts
6
Pitch Spacing
2.54mm
Contact Material
Copper Alloy
Contact Plating
Gold
Contact Termination
Surface Mount Horizontal
Row Pitch
7.6mm
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
C
D
G
H
A
B
E
F
DETAIL
Global Connector Technology Ltd. - SIM2065 : SIM Card Connector, Reciever Type, 6 Pin, SMT, Profile Options 1.8/2.0mm
DATE
REV
By
DRAWING
RELEASE
13/09/07
PKN
A
1
1
ECN070913A
15/05/08
PKN
B
SPECIFICATION
11/06/09
MODIFIED
ASE
C
2
2
3
3
4
4
Third Angle Projection
硬纸板
气泡墊
卷筒
Dimensions in mm
(Except as noted)
Tolerances
5
5
电周波
Description:-
Part Number:-
SIM CARD CONNECTOR, RECIEVER TYPE, 6 PIN,
SMT, PROFILE OPTIONS: 1.8/2.0MM
C
THIS DRAWING IS CONFIDENTIAL AND MUST NOT BE
COPIED OR DISCLOSED WITHOUT WRITTEN CONSENT
SIM2065
1.The 1st & Last 200-300mm at the leading & tail of the CARRY TAPE will not be used.CARRY TAPE
Notes 注意 :
前部分与尾部分各留出 200-300mm 长度不装产品
2.Each cavity will hold 1pc. Placement methods are shown in the diagrams. 每穴放置 1pc 产品,放置
方式如图所示
3.After the packing machine filled the REEL,tangle the REEL one more loop with protection tape,
stick adhesive tape on the four quardrants of the REEL, to aviod out-spreading. Stick 1pc. of label on
each REEL.
包装机包好后,再缠上一圈电周波,在 REEL 的四个极点贴上胶带 ,以防止 REEL 张开,每 REEL 贴 1PC 标
签
4. Method of Packing is Hot-Melting. 包装方式是热熔式
5. Firstly put a water-proof bag at the bottom of the carton box, then place 1pc. of hard cardboard on
top, following with 1pc. of bubble-pad, and at the four corners, place the triangular pads, then place
those filled REEL into the center of the carton box. Between the REEL, place 1pc. of bubble-pad as
the separator, until 5pc. of REEL are filled in the box. Then place 1pc of bubble-pad & 1pc. of hard
cardboard on top, close the carton by plastic tape lastly. 先在纸箱底部套上一防水袋 ,再墊上 1pc 硬纸
板后再墊上 1pc 气泡墊,四角墊上三角墊,度然后把装好产品的 REEL 放进纸箱中,每 REEL 之间隔 1pc 气
泡墊,依次把 5 REEL 产品放到纸箱中,上面再墊上各 1pc 气泡墊及硬纸板 , 最后用胶带封箱 .
6. The peel-off force between the COVER TAPE & CARRY TAPE is: 0.1N-0.7N (variation within
0.3N). Peel-off angle:165-175 degree; Speed of peel-off: 250mm-300mm/min. COVER
TAPE 与 CARRY TAPE 剥离力 :0.1N-0.7N ( 跳动量在 0.3N 以内 ) 剥离角度 :165-175 度 ; 剥离速度 :
250mm-300mm/ 分钟
6
6
Date:-
13 SEP 07
7
Scale
7
NTS
Revision
www.globalconnectortechnology.com
三角墊
C
标签
GC
纸箱
Material
See Note
Drawn by
PKN
8
8
E & OE
Sheet No.
2/2
A
B
C
D
E
F
G
H