142-4407-101 JOHNSON/EMERSON, 142-4407-101 Datasheet

RF/COAXIAL, SMA RP PLUG, R/A 50OHM CRIMP

142-4407-101

Manufacturer Part Number
142-4407-101
Description
RF/COAXIAL, SMA RP PLUG, R/A 50OHM CRIMP
Manufacturer
JOHNSON/EMERSON
Datasheet
1.142-4407-101.pdf (2 pages)

Specifications of 142-4407-101

Body Style
Right Angle Plug
Coaxial Termination
Solder / Crimp
Rg Cable Type
RG-58, 141, 303
Contact Material
Beryllium Copper
Connector Type
SMA RP Coaxial
Impedance
50ohm
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
SMA 50 Ohm Reverse Polarity
Right Angle Crimp Type Plug -
Captivated Contact
Johnson Components
RG-58/U, 141, 303
CABLE TYPE
CABLE GROUP
RG-58/u,
141, 303
TM
• P.O. Box 1732 • Waseca, MN 56093-0832 • 1-800-247-8256 • Fax: 507-833-6287 • www.johnsoncomponents.com
GOLD PLATED
142-4407-101
PART NUMBER CRIMP HEX
142-4407-101
142-4407-106
NICKEL PLATED
142-4407-106
.213 (5.41)
.213 (5.41)
1. Identify connector parts. (3 piece parts)
2. Strip cable to dimensions shown. Do not nick braid or cen-
3. Flare braid and slide cable into body making certain that
4. Arrange braid uniformly around crimp stem. Slide crimp
ter conductor. When stripping LMR-100 low loss cable,
remove foil back to where cable jacket is stripped. A wire
stripper of correct size is recommended for this step. Twist
stranded center conductor into tight bundle and tin (op-
tional). Slide crimp sleeve onto cable as shown.
the cable insulation bottoms on center contact. Solder
center conductor to contact through the rear access port.
Use a minimum amount of solder for a full fillet joint. .020
(0.51) diameter solder is recommended.
sleeve over braid and crimp securely using recommended
crimp tool. Place expansion cap in access port and seat
with .187 (4.75) diameter flat punch. Shrink heat shrink
tubing over crimp sleeve if applicable.
INCHES (MILLIMETERS)
CUSTOMER DRAWINGS AVAILABLE UPON REQUEST

Related parts for 142-4407-101

Image
Part Number
Description
Manufacturer
Datasheet
Request R
142-4407-001
Part Number:
142-4407-001
Description:
RF/COAXIAL, SMA RP PLUG 50OHM CRIMP/SLDR
Manufacturer:
JOHNSON/EMERSON
Datasheet:
142-4407-001.pdf (2 pages)
142-0701-631
Part Number:
142-0701-631
Description:
CONN JACK 4HOLE FLANGE MOUNT GOL
Manufacturer:
Emerson Network Power
Datasheet:
142-0701-631.pdf (3 pages)
142-0701-306
Part Number:
142-0701-306
Description:
CONN JACK RCPT R/A SMA PCB
Manufacturer:
Emerson Network Power
Datasheet:
142-0701-301.pdf (3 pages)
142-0701-621
Part Number:
142-0701-621
Description:
CONN JACK FLANGE MOUNT GOLD
Manufacturer:
Emerson Network Power
Datasheet:
142-0701-621.pdf (5 pages)
142-0701-211
Part Number:
142-0701-211
Description:
CONN JACK BULKHEAD PCB .281" GOL
Manufacturer:
Emerson Network Power
Datasheet:
142-0701-211.pdf (1 page)

142-4407-101 Summary of contents

Page 1

... Arrange braid uniformly around crimp stem. Slide crimp sleeve over braid and crimp securely using recommended crimp tool. Place expansion cap in access port and seat with .187 (4.75) diameter flat punch. Shrink heat shrink tubing over crimp sleeve if applicable. 142-4407-101 .213 (5.41) 142-4407-106 .213 (5.41) INCHES (MILLIMETERS) ...

Page 2

... P.O. Box 1732 • Waseca, MN 56093-0832 • 1-800-247-8256 • Fax: 507-833-6287 • www.johnsoncomponents.com RF High Potential Withstanding Voltage: (Vrms minimum, tested at 4 and 7 MHz) † Connectors for RG-316; LMR-100, 195, 200 ................................... 500 Connectors for RG-58, RG-142, LMR-240, uncabled receptacles ... 670 MECHANICAL RATINGS Engagement Design: MIL-C-39012, Series SMA Right Angle Engagement/Disengagement Force: 2 inch-pounds maximum Cabled Connectors 1 ...

Related keywords