CTS13227X9010D2P Vishay, CTS13227X9010D2P Datasheet - Page 16

• Manufacturer Part Number: CTS13227X9010D2P
• Description: CAPACITOR, 220UF 10V CAPACITOR, 220UF 10V
• Manufacturer: Vishay
• Series: CTS13r

Specifications of CTS13227X9010D2P

• Capacitance: 220UF
• Voltage Rating, Dc: 10V
• Capacitor Dielectric Type: TANTALUM ELECTROLYTIC
• Tolerance,: 10%
• Tolerance, -: 10%
• Temp, Op. Min: -55(DEGREE C)
• Temp, Op.: ROHS COMPLIANT

CTS1, CTS13, 749DX
Vishay Sprague
PERFORMANCE CHARACTERISTICS
1. Operating temperature:
2. Capacitance and tolerance:
3. Reverse voltage:
4. Surge voltage:
Table 1
5. Leakage current:
Table 2
www.vishay.com
69
749DX/CTS1
Capacitance measured at 100 Hz and + 25 °C shall be
within the specified tolerance limits of the nominal rating.
Capacitance measurement shall be made by means of a
polarized capacitance bridge. The polarizing voltage shall
be of 2.2 V. The maximum voltage applied during
measurements shall be 1.0 V
These capacitors are capable of withstanding peak
voltage in the reverse direction equal to: 15 % of the rated
DC voltage at + 25 °C, 5 % of the rated DC voltage at
+ 85 °C.
Capacitors shall withstand the surge voltage applied in
series with a 1000 W resistor, at the rate of 1.5 min on,
5.5 min off, for 1000 successive test cycles at + 85 °C or
at + 125 °C. After test, dissipation factor and leakage
current shall meet the initial requirements at + 25 °C (see
below), capacitance change shall not exceed ± 10 % of
initial value at + 25 °C.
Rated voltage U
minutes with a resistor of 1000 Ω in series with each
capacitor,
measurements. The leakage current shall not exceed the
following limits:
PRODUCT
+ 85 °C to + 125 °C with linear voltage derating
to category voltage UC (only for types CTS1, 749DX).
- 55 °C to + 85 °C with rated DC voltage UR applied,
CTS13
TEMPERATURE
TYPE
+ 125 °C
+ 25 °C
+ 85 °C
before
SURGE VOLTAGE
R
shall be applied to capacitors during five
AT + 85 °C
1.30 U
1.30 U
making
R
R
12.5 µA whichever is greater
10 µA whichever is greater
1 µA whichever is greater
rms
CTS1/CTS13/749DX
0.125 C
at 100 Hz and + 25 °C.
DC
0.01 C
0.1 C
For technical questions, contact:
SURGE VOLTAGE
R
R
leakage
R
x U
x U
Hermetically Sealed, Axial-Lead
x U
AT + 125 °C
R
1.30 U
R
R
or
or
or
-
to CECC Specifications
C
current
[e-mail]
6. Dissipation factor:
Table 3
7. Stability at low and high temperature:
Table 4
8. Impedance:
Table 5
9. Life test:
Table 6
Note
Note
Note
+ 125 °C
PRODUCT
The dissipation factor, when measured at 100 Hz, shall not
exceed the values below:
+ 25 °C
+ 85 °C
Capacitance change with temperature shall not exceed
the limits of the following table, leakage current and
dissipation factor shall be within the limits specified in
Tables 2 and 3.
The impedance measured at 100 kHz and 25 °C shall not
exceed the following values
After 2000 h at + 85 °C with rated DC voltage applied,
or after 2000 h at + 125 °C with category DC voltage
applied (for types CTS1, 749DX only) capacitors shall
meet the requirements in table 6.
- 55 °C
CTS13
749DX
TEMP.
TYPE
CTS1
TEMPERATURE
(1)
(2)
(3)
CASE CODE
+ 125 °C
Not applicable for CTS13
Not applicable for CTS13
Not applicable for C
(1)
+ 85 °C
- 55 °C
C
D
A
B
C
CAPACITANCE
R
initial value
U
at + 25 °C
CHANGE
± 10 % of
(2)
12 %
R
9 %
6 %
9 %
Within
≤ 1900 C
CTS1/CTS13
R
R
≤ 0.68 µF
U
11 %
11 %
14 %
R
DISSIPATION
8 %
:
requirement
> 1900
at + 25 °C
FACTOR
CTS1/CTS13/749DX
Within
initial
Document Number: 42073
Z (Ω)
+ 12 %
+ 15 %
- 10 %
C
R
10 %
10
8 %
6 %
5
2
1
Revision: 02-Nov-09
≤ 100
-
(3)
DC LEAKAGE
749DX
Within 125 %
requirements
CURRENT
at + 25 °C
of initial
C
R
10 %
11 %
8 %
> 100
-