135D256X0125T6 Vishay, 135D256X0125T6 Datasheet - Page 9
![Wet Tantalum Capacitors Tantalum-Case With Glass-to-Tantalum Hermetic Seal](/photos/29/21/292196/135d_sml.jpg)
135D256X0125T6
Manufacturer Part Number
135D256X0125T6
Description
Wet Tantalum Capacitors Tantalum-Case With Glass-to-Tantalum Hermetic Seal
Manufacturer
Vishay
Series
135Dr
Datasheet
1.135D276X9125F6E3.pdf
(14 pages)
Specifications of 135D256X0125T6
Voltage Rating
125 Volts
Esr
3.2 Ohms
Operating Temperature Range
- 55 C to + 85 C
Termination Style
Axial
Dimensions
9.53 mm Dia. x 19.46 mm L
Leakage Current
8 uA
Product
Tantalum Wet Hermetically Sealed
Capacitance
25 uF
Tolerance
20 %
Package / Case
Case T
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
10. Ripple Life Test at + 85 °C: Capacitors shall be tested
10.1 When tested as specified above, capacitors shall meet
11. Reverse Voltage Test: Capcitors shall withstand a
11.1 Following the reverse voltage test, the DC leakage
12. Mechanical Shock Test: Capacitors shall withstand a
12.1 Following the mechanical shock test, capacitors shall
13. High Frequency Vibration: Capacitors shall withstand
13.1 Capacitors shall be securely fastened by means of
14. Random Vibration: Capacitors shall withstand random
Document Number: 40024
Revision: 15-Nov-10
in accordance with Military Specification MIL-C-39006
except that:
a) Operation Conditions: This test shall be run at a
b) Applied DC voltage shall be reduced so that the
the following requirements:
a) The DC leakage current at + 25 °C and at + 85 °C
b) The capacitance shall not change more than ± 15 %
c) The dissipation factor shall not exceed the original
d) Visual examination: There shall be no damage,
reverse voltage of 3 V
for 2000 h. The capacitors shall then be restabilized for
24 h at 85 °C with rated DC forward potential applied
through a 1000 Ω resistor.
current shall not be in excess of the original
requirement; the equivalent series resistance shall not
exceed 200 % of the initial requirement; the
capacitance value shall not be less than 90 % of the
initial measurement.
shock of 500 g when tested in accordance with method
213 of MIL-STD-202, test condition D.
be examined for evidence of mechanical damage and
leakage of electrolyte. Capacitance, equivalent series
resistance, and DC leakage current shall meet the initial
requirements.
vibration from 10 Hz to 2000 Hz at 80 g without internal
damage when tested in accordance with MIL-STD-202,
method 204, test condition H. Electrical measurements
made while under these conditions shall show no
intermittent contacts, open circuits or short circuits.
suitable component clips or brackets.
vibration at all levels up to 51 g RMS overall when
tested in accordance with MIL-STD-202, method 214,
test condition II K. The test shall be conducted for 1.5 h
in each of three mutually perpenticular directions.
RMS ripple current levels specified in the “Standard
and Extended Ratings Table”.
peak AC voltage plus DC voltage shall not exceed
the rated voltage of the capacitor in either the
forward or reverse direction.
shall not exceed the original requirements.
from the initial measured value.
requirements.
obliteration of marking or leakage of electrolyte.
frequency of 40 kHz ± 2 kHz sinusoidal and at the
Wet Tantalum Capacitors Tantalum-Case with Glass-to-Tantalum
DC
at + 85 °C or 2 V at + 125 °C
Hermetic Seal for - 55 °C to + 200 °C Operation
For technical questions, contact:
14.1 Electrical measurements made during the test shall
15. Pull Test: Leads shall withstand a tensile stress of
16. Lead Bend Test: Leads shall meet the bend test
17. Moisture Resistance: Capacitors shall withstand the
18. Reduced Pressure: Capcitors shall be stabilized at a
19. Seal Test:
19.1 Capacitors shall be tested in accordance with
20. Thermal shock: Capacitors shall be subjected to 300
20.1 Following the thermal shock test, capacitor leakage
21. Marking: Capacitors shall be marked with Sprague, the
21.1 Polarity shall be indicated by plus signs (+) adjacent to
show no intermittent contacts. open circuits or short
circuits.
3 lbs. (1.4 kg) for 30 s applied axially in accordance with
MIL-STD-202, method 211, test condition A.
specified in Military Standard MIL-STD-202, method
211 A, condition C except that the number of bends
shall be 4.
moisture resistance cycling test specified in Military
Standard MIL-STD-202, method 106, without departure
from the original limits of capacitance, equivalent series
resistance and DC leakage current.
reduced atmospheric pressure of 0.82
mercury for a period of 5 min. Rated DC voltage shall be
applied for 1 min. Capacitors shall not flash over nor
shall end seals be damaged by this nor should the
capacitors
capacitance, equivalent series resistance or leakage
current is concerned.
MIL-STD-202, method 112, test condition C, procedure
IIIa. Specimens shall be pressurized at 4 atmospheres
(gage) for 4 h.
cycles of thermal shock in accordance with Military
specification MIL-C-39006.
current shall not exceed twice the initial requirement.
Sprague type (135D); rated capacitance and tolerance
(the tolerance shall be coded, using the list shown in
How to Order); rated DC working voltage at
the standard EIA date code of manufacture.
the positive terminal.
tantalum@vishay.com
be
electrically
effected
"
www.vishay.com
[20.83 mm] of
insofar
Vishay
135D
+ 85 °C;
as
9