LQ0B192 Sharp Microelectronics, LQ0B192 Datasheet - Page 17

• Manufacturer Part Number: LQ0B192
• Description: CCFL Fluorescent Lamps CCFT LQ10D421
• Manufacturer: Sharp Microelectronics

Specifications of LQ0B192

• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

10. Display Quality
11．Handling Precautions
.
12.Packing form
i) In case of attaching protective board over the LCD, be careful about the optical interface fringe etc. which
n)Cold cathode fluorescent lamp in LCD panel contains a small amount of mercury, please follow local
a) Be sure to turn off the power supply when inserting or disconnecting the cable.
b) Be sure to design the cabinet so that the module can be installed without any extra stress such as
c) Since the front polarizer is easily damaged, pay attention not to scratch it.
d) Wipe off water drop immediately. Long contact with water may cause discoloration or spots.
e) When the panel surface is soiled, wipe it with absorbent cotton or other soft cloth.
f) Since the panel is made of glass, it may break or crack if dropped or bumped on hard surface.
g) Since CMOS LSI is used in this module, take care of static electricity and injure the human earth
h) Protection film is attached to the module surface to prevent it from being scratched .
j) Do not expose the LCD panel to direct sunlight. Lightproof shade etc. should be attached when LCD panel
k) Connect GND to 4 place of mounting holes to stabilize against EMI and external noise.
l) There are high voltage portions on the backlight and very dangerous. Careless touch may lead to
m) When handling LCD modules and assembling them into cabinets, please be noted that long-term
o) Be sure not to aplly tensile stress to the lamp lead cable.
p) Do not expose the LCD panel to direct sunlight. Lightproof shade etc. should be attached when LCD
q) Be careful of a back light lead not to pull by force at the time of the wiring to an inverter, or line processing.
r) When install LCD modules in the cabinet, recommended torque value is “0.294±0.02N･m
s) Liquid crystal contained in the panel may leak if the LCD is broken. Rinse it as soon as possible if it gets
t) Notice:Never dismantle the module , because it will cause failure.
u) Be careful when using it for long time with fixed pattern display as it may cause afterimage.
v) Adjusting volume have been set optimally before shipment, so do not change any adjusted value.
w) If a minute particle enters in the module and adheres to an optical material, it may cause display non-
Incoming Inspection Standard.
degrades display quality.
The display quality of the color TFT-LCD module shall be in compliance with the
is used under such environment.
ordinances or regulations for disposal.
warp or twist.
Handle with care.
Peel the film off slowly , just before the use, with strict attention to electrostatic charges.
Blow off 'dust' on the polarizer by using an ionized nitrogen.
electrical shock. When exchange lamps or service, turn off the power without tail.
storage in the environment of oxidization or deoxidization gas and the use of such materials as reagent,
solvent, adhesive, resin, etc. which generate these gasses, may cause corrosion and discoloration of the
LCD modules.
panel is used under such environment.
(3.0±0.2kgf･cm)”.
Be sure to confirm it in the same condition as it is installed in your instrument.
inside your eye or mouth by mistake.
If adjusted value is changed, the specification may not be satisfied.
uniformity issue, etc. Therefore, fine-pitch filters have to be installed to cooling and inhalation hole if you
intend to install a fan.
Product country
Piling number of cartons
Packing quantity in one carton
Carton size [mm]
Total mass of one carton filled
with full modules
Packing form is shown
when handling. Observe all other precautionary requirements in handling electric components.
JAPAN
７（Max）
20
525 (W)×309(D)×377(H)
17.5kg
Fig.4