4171700XX-3 Digital View Inc, 4171700XX-3 Datasheet

Page 1

PC, DVI, VIDEO INTERFACE CONTROLLER CONTENTS Page: 2. Introduction, How to Proceed, Usage Note, Disclaimer 3. System design – Diagram of a suggested system 4. Assembly notes – Important information about system elements 6. Connection & Operation – How to ...

Page 2

Introduction Designed for LCD monitor and other flat panel display applications, the SVH-1920 feature rich interface controller for : TFT (active matrix) LCD panels of 1920x1200, 1920x1080, 1920x480, 1600x1200, 1680x1050, 1440x900, 1366x768, 1280x1024, 1280x800, 1280x768 1024x768, 1024x600, 800x600, ...

Page 3

SYSTEM DESIGN A typical LCD based display system utilizing this controller is likely to comprise the following: Summary: 1. LCD panel 2. LCD controller card, SVH-1920+ 3. LCD signal cable (use for LVDS panel) 4. LCD signal cable (use for ...

Page 4

ASSEMBLY NOTES This controller is designed for monitor and custom display projects using 1920x1200 or 1920x1080 or 1920x480 or 1600x1200 or 1680x1050 or 1440x900 or 1366x768 or 1280 x 1024 or 1024 x 768 or 1024x600 or 800x600 or 640x480 ...

Page 5

DVI-D input cable : Plug the DVI cable to the connector P3 on the controller board 19. Analog RGB Input : As this may affect regulatory emission test results and the quality of the signal to the controller a ...

Page 6

CONNECTION & OPERATION CAUTION: Never connect or disconnect parts of the display system when the system is powered up as this may cause serious damage. CONNECTION Connection and usage is quite straight forward (it is useful to have the relevant ...

Page 7

LCD DISPLAY SYSTEM SETTINGS NOTE: By way of explanation the following refers to a set of sample buttons that may be obtained as an option. In addition to power on/off and connection for backlight brightness the controller provides an On ...

Page 8

OSD functions Picture : Volume Brightness Contrast Saturation Hue ** Sharpness* Backlight Position Aspect / Size 4 Blue Only Specifications subject to change without notice © Digital View Ltd – Doc Ver 1.1: 8 Nov, 2010 (SVH-1920+_manual.doc) ### Increase/decrease volume ...

Page 9

Source : Select the input video signal Main Port Change 4 VGA DVI HD/SD SDI 1*** HD/SD SDI 2*** Composite 1 Composite 2*** S-Video 1 S-Video 2*** Component 1 Component 2*** PIP Port change4 PIP Off / Composite 1 / ...

Page 10

De-interlacing Mode* 4 Auto Power : Video Standard (SD)* : Auto / NTSC / NTSC 4.43 / PAL / PAL M / SECAM Gamma : 0.6 / 0.7/ 0.8 / 1.0 / 1.6 / 1.8 / 1.9 / 2.0 / ...

Page 11

User setting : Reset All to Defaults : Resume all color temperature settings to the default values. Hot Key 4 Hot key 1 : Volume / Brightness / Contrast / Inputs / Aspect Ratio/ Zoom / Freeze / PIP ...

Page 12

CONNECTORS, PINOUTS & JUMPERS The various connectors are: Summary: Connectors Ref Purpose CN3 Panel signal for TTL panel CN7 Audio board connector CN8 RS-232 serial control CN9 Ambient light sensor connector CNA1 Auxiliary power output CNB1 Backlight inverter CNC1 OSD ...

Page 13

PP2/PP3 Power input (alternative) PP4 External panel power input PP5 Power input SW3 Panel selection SW4 Function selection Specifications subject to change without notice © Digital View Ltd – Doc Ver 1.1: 8 Nov, 2010 (SVH-1920+_manual.doc) DC power Molex 2 ...

Page 14

Summary: Jumpers setting Ref Purpose JA2 On board +3.3V logic power enable JA3 Panel power voltage select CAUTION: Incorrect setting can damage panel JA5 Panel power voltage select CAUTION: Incorrect setting will cause panel damage JA6 Panel power voltage select ...

Page 15

Table 1 : Panel voltage setting table : Input voltage via PP2/PP3, PP5 Panel Voltage 3.3V 12VDC 5V 12V CAUTION: Incorrect setting can damage panel & controller Input voltage via PP2/PP3, PP5 Panel Voltage 3.3V 5V 24VDC** 12V 18V CAUTION: ...

Page 16

Input voltage via PP4 Panel Voltage 3. 18VDC* 12V 18V * Maximum current for 3.3V 7A, Maximum current for 12V = 5A, Maximum current for 18V = 3.5A JA3, JA5 & ...

Page 17

Table 2 : DIP Switch selection – SW3 Pos #1 Pos #2 Pos #3 OFF OFF OFF OFF ON OFF OFF OFF ON OFF ON ON OFF OFF OFF ON OFF OFF OFF ON OFF ...

Page 18

CN3 – Panel connector: HIROSE DF20G-50DP-1V (Matching type : DF20A-50DS-1C) PIN SYMBOL Reserved 12 Reserved P_G0 16 P_G1 17 P_G2 18 P_G3 19 P_G4 20 P_G5 ...

Page 19

VOLSEL1 4 TUNAUDSEL 5 CLK/CNT 6 GND 7 +12V/+24V GND CN8 – RS-232 serial control: JST B6B-XH-A (Matching type : XHP-6) PIN SYMBOL 1 SDATA 2 SCLK 3 VCC 4 5 GND 6 RXD CN9 – ...

Page 20

CNV5 – Auxiliary Video input connector, DIL socket header 13x2 PIN ...

Page 21

GND 28 GND 29 TXBC+ 30 TXBC- 31 GND 32 GND 33 VDD (3,3V/5V) 34 VDD (3,3V/5V) 35 VDD (3,3V/5V) 36 VDD (3,3V/5V VDD +12V / +18V 39 VDD +12V / +18V 40 VDD +12V / +18V ...

Page 22

LED1 – Status LED connector: 3-pin header PIN Analog VGA way connector PIN SYMBOL DGND 6 AGND 7 AGND 8 AGND 9 DDC_5V 10 DGND 11 12 ...

Page 23

PP5 - 12V/24VDC power supply PIN 1 2 Specifications subject to change without notice © Digital View Ltd – Doc Ver 1.1: 8 Nov, 2010 (SVH-1920+_manual.doc) DESCRIPTION +12V / +24VDC Ground Page ...

Page 24

CONTROLLER DIMENSIONS Ready-made 3D Pro-E (SLDPRT) drawing files - Save time and effort for your system volumetric analysis design. Includes jpg file previews. Please go to download at http://www.digitalview.com/drawing/SVH-1920+_-2X_3D_Drawing.zip. The maximum thickness of the controller is 20.65mm with or without ...

Page 25

APPLICATION NOTES USING THE CONTROLLER WITHOUT BUTTONS ATTACHED This is very straightforward: • Firstly setup the controller/display system with the buttons. With controls attached and display system active make any settings for colour, tint and image position as required then ...

Page 26

Design Guideline for making VR circuitry : CNB1 – Backlight inverter connector: JST B5B-XH-A (Matching type : XHP-5) PIN SYMBOL 1 GND 2 VBKL 3 BLCTRL 4 BVR_WIP 5 BVR_A CNC1 – Control switch, JST B12B-XH-A (Matching type : XHP-12) ...

Page 27

TROUBLESHOOTING General A general guide to troubleshooting a flat panel display system it is worth considering the system as separate elements, such as: Controller (jumpers, PC settings) Panel (controller, cabling, connection, panel, PC settings) Backlight (inverter, cabling, backlight tubes) Cabling ...

Page 28

SPECIFICATIONS Panel compatibility No. of colours Panel power Panel signal Vertical refresh rate Display clock maximum ADC clock maximum DVI differential input clock maximum Graphics formats Graphics auto mode detect Standard input at source (analog RGB) Video formats Video inputs ...

Page 29

APPENDIX I – SIGNAL SUPPORT MODE TABLE ARGB (P1) PORT : Mode Resolution T_70 720x400 T_70 720x400 V_60 640x480 V_60 640x480 V_60 640x480 V_72 640x480 V_72 640x480 V_72 640x480 V_75 640x480 V_75 640x480 V_75 640x480 SV_56 800x600 SV_56 800x600 SV_56 ...

Page 30

X_60 1024x768 X_60 1024x768 X_70 1024x768 X_70 1024x768 X_70 1024x768 X_75 1024x768 X_75 1024x768 X_75 1024x768 SX_60 1280x1024 SX_60 1280x1024 SX_60 1280x1024 SX_75 1280x1024 SX_75 1280x1024 SX_75 1280x1024 UX_60 1600x1200 UX_60 1600x1200 UX_60 1600x1200 WUX_60 1920x1080 WUX_60 1920x1080 WUX_60 1920x1080 ...

Page 31

COMPOSITE, S-VIDEO & COMPONENT VIDEO INPUT PORT : System Resolution Horizontal freq [KHz] NTSC 720x480i 15.7 NTSC 4.43 720x480i 15.7 PAL 720x576i 15.6 PAL M 720x576i 15.6 SECAM 720x576i 15.6 Specifications subject to change without notice © Digital View Ltd ...

Page 32

Appendix II – RS-232 control protocols RS-232 Serial control (Baud rate 2400, Physical connection : Controller side Connector interface : CN8 Mating connector : JST XHP Mating face of CN8 PIN# Description 4 RS-232 Tx ...

Page 33

Commands to implement switch mount control buttons Function Command Menu button 0xf7 Select-down 0xfa button Select-up button 0xfb Right/+ button 0xfc Left/- button 0xfd 2. Parameter setting - immediate, relative, reset and query Function Command Volume control - 0x80, ...

Page 34

OSD H position 0x90, nnn | “+” | “-” | “r” | “R” | “?” OSD V position 0x91, nnn | “+” | “-” | “r” | “R” | “?” OSD 0x92, Transparency n | “+” | “-” | ...

Page 35

Component Only) “S” | “s”| “?” GAMMA value 0x9d, select n | “r” | “R” “?” Auto power off 0x9f, “0” | “1” | “r” | “R” | “?” Hotkey 1 0xa0, “1” “r” | “R” | “?” ...

Page 36

PIP brightness 0xa2, control nn | “+” | “-” | “r” | “R” | “?” PIP contrast 0xa3, control nn | “+” | “-” | “r” | “R” | “?” PIP H position ...

Page 37

Vertical Size 0xb0, nnn | “+” | “-” | “r” | “R” | “?” Horizontal Pan 0xb1, nnn | “+” | “-” | “r” | “R” | “?” Vertical Pan 0xb2, nnn | “+” | “-” | “r” | “R” ...

Page 38

OSD status 0xbb enquiry OSD turn off 0xbd Set gamma data 0xbf, mm, c, “?” for user defined gamma curve 0xbf, “R” | “r” 0xbf, mm Backlight control 0xe0 “+” | “-” | “R” | “r” ...

Page 39

Backlight Invert 0xe7 “0” | “1” | “R” | “r” ”?” Red Offset for 0xe8, selected colour temperature nn | “+” | “-” | “r” | “R” | “?” Green Offset for 0xe9, selected colour temperature nn | “+” | ...

Page 40

Send Display Mark RS232 Code: “0xF1 0x53 0x21” Return Code: “0xF1 0x53 0x21 0x31” Clear Display 0xF1, Mark ”C” Return “1” e.g Clear Display Mark RS232 Code: “0xF1 0x43” Return Code: “0xF1 0x43 0x31” Display Mark 0xF1, Horizontal |”H” ...

Page 41

Video de-interlace 0xca, method “0” | “1” “r” | “R” “?” Query BIOS 0xcb, “0” version Query PCBA 0xcb, “1” number Reset parameter 0xce Wide Screen 0xd9, Mode Selection “0” | “1”| “2” “r” | “R” “?” Specifications subject to ...

Page 42

The following commands for sending texts by using RS-232 command. Function Command Send Line 0xF0, |”S” |”LL”|”TEXT”| “0x0A” Return “1” e.g Display “Send Text” message on screen: RS232 Code:“0xF0 0x53 0x30 0x31 0x53 0x65 0x6E 0x64 0x20 0x54 0x65 0x78 ...

Page 43

Set background Transparency value is 8 RS232 Code: “0xF0 0x42 0x38” Return Code: “0xF0 0x42 0x38 0x38” Text Window 0xF0, Horizontal Size |”X” |”SSS”| Return “nnn” e.g Set Text Window Horizontal Size = 640 pixels ( 0x280 (HEX)) RS232 Code: ...

Page 44

Appendix I – Mapping definition • Definition of Mapping A : Specifications subject to change without notice © Digital View Ltd – Doc Ver 1.1: 8 Nov, 2010 (SVH-1920+_manual.doc Page ...

Page 45

Definition of Mapping B : Specifications subject to change without notice © Digital View Ltd – Doc Ver 1.1: 8 Nov, 2010 (SVH-1920+_manual.doc Page ...

Page 46

Appendix IV – Auto Color Gain The Auto Color Gain function is supported in the ARGB or Component video mode only and is designed to calibrate the controller to the incoming video signal. In order to calibrate correctly, the display ...

Page 47

Appendix V – DV remote control unit work for SVH-1920+ P/N 559000106-3 : DigitalView remote control unit (without DV logo silk screen printing) P/N 559000105-3 : DigitalView remote control unit (with DigitalView logo silk screen printing) BUTTON POWER BUTTON Soft ...

Page 48

Appendix VI – Function description for de-interlacing mode AFM, TNR, MADI, DCDi AFM = Auto Film Mode : frame based method which used for the input ODD and EVEN fields have a fixed relation between each other, ...

Page 49

Appendix IX - Inverter Interface Board P/N 416040010-3 [OPERATE UNDER 12VDC POWER INPUT ENVIRONMENT] The Inverter interface board provides interface to drive up the high current consumption panel inverter in excess of 3.5A. This board enables current ...

Page 50

Illustrated Diagram PP1 - 12VDC power supply – input, Power header 4 ways 0.156” pitch PIN PP2 – Alternate 12VDC power supply – input, Terminal Block 2 poles PIN PP3 – 12VDC ...

Page 51

CNB3 – Inverter interface to backlight inverter, JST B8B-XH-A PIN SYMBOL 1 VLCD12 2 VLCD12 3 GND 4 GND 5 VLCD12 6 BLCTRL 7 BVR_WIP 8 BVR_A Specifications subject to change without notice © Digital View Ltd – Doc Ver ...

Page 52

Appendix X - Audio Add-on Board P/N 416940020-3 [OPERATE UNDER 12VDC POWER INPUT ENVIRONMENT] The Audio add-on board P/N 416940020-3 design for connection with DV controllers on the audio connector CN7. It provides audio input ports and output port for ...

Page 53

CN3 : Controller interface connector Pin Number 1 +5V 2 Left trimpot chip select 3 Right trimpot chip select 4 Trimpot serial data 5 Trimpot serial clock 6 Digital Ground 7 +12V 8 Audio input left 9 Audio input right ...

Page 54

WARRANTY The products are warranted against defects in workmanship and material for a period of three (3) year from the date of purchase provided no modifications are made to it and it is operated under normal conditions and in compliance ...

Page 55

... CONTACT DETAILS Digital View has offices in Asia, Europe and USA : USA Digital View Inc. 18440 Technology Drive Building 130 Morgan Hill, California, 95037 USA Tel: (1) 408-782 7773 Fax: (1) 408-782 7883 Sales: ussales@digitalview.com EUROPE Digital View Ltd. 6 Marylebone Passage, London, W1W 8EX, UK ...