MAX16826ATJ+ Maxim Integrated Products, MAX16826ATJ+ Datasheet - Page 8

• Manufacturer Part Number: MAX16826ATJ+
• Description: LED Drivers Programmable Four-St ring HB LED Driver w
• Manufacturer: Maxim Integrated Products

Specifications of MAX16826ATJ+

• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

Programmable, Four-String HB LED Driver with
Output-Voltage Optimization and Fault Detection
8
PIN
2, 3
10
11
12
13
14
15
16
17
1
4
5
6
7
8
9
_______________________________________________________________________________________
SYNC/EN
NAME
COMP
PGND
RTCT
DIM1
DIM2
DIM3
DIM4
GND
CSS
OVP
RSC
SDA
SCL
CS1
FB
Power Ground
Analog Ground
Timing Resistor and Capacitor Connection. A resistor, R19 (in the Typical Application Circuit), from V
RTCT and a capacitor C33, from RTCT to GND set the oscillator frequency. See the Oscillator section to
calculate RT and CT component values.
Synchronization and Enable Input. There are three operating modes:
Soft-Start Timing Capacitor Connection. Connect a capacitor from CSS to GND to program the required soft-
start time for the switching regulator output voltage to reach regulation. See the Soft-Start (CSS) section to
calculate C
Switching Regulator Compensation Component Connection. Connect the compensation network between
COMP and FB.
Switching Regulator Feedback Input. Connect FB to the center of a resistor-divider connected between the
switching regulator output and GND to set the output voltage. FB is regulated to a voltage set by an internal
register. See the Setting Output Voltage section for calculating resistor values.
Switching Regulator Overvoltage Input. Connect OVP to the center of a resistor-divider connected between the
switching regulator output and GND. For normal operation, configure the resistor-divider so that the voltage at
this pin does not exceed 1.25V. If operation under load dump conditions is also required, configure the resistor-
divider so that the voltage at OVP is less than 1.25V.
Slope Compensation Resistor and PWM Comparator Input Connection. Connect a resistor, R17, from RSC to
the switching current-sense resistor to set the amount of the compensation ramp. See the Slope Compensation
(RSC) section for calculating the value.
I
I
LED String 1 Logic-Level PWM Dimming Input. A high logic level on DIM1 enables the current sink to operate at
the maximum current as determined by its sense resistor and internal register value. A low logic level disables
the current source.
LED String 2 Logic-Level PWM Dimming Input. A high logic level on DIM2 enables the current sink to operate at
the maximum current as determined by its sense resistor and internal register value. A low logic level disables
the current source.
LED String 3 Logic-Level PWM Dimming Input. A high logic level on DIM3 enables the current sink to operate at
the maximum current as determined by its sense resistor and internal register value. A low logic level disables
the current source.
LED String 4 Logic-Level PWM Dimming Input. A high logic level on DIM4 enables the current sink to operate at
the maximum current as determined by its sense resistor and internal register value. A low logic level disables
the current source.
LED String 1 Current-Sense Input. CS1 is regulated to a value set by an internal register. The regulation voltage
can be set between 97mV and 316mV.
2
2
SYNC/EN = LOW: Low current shutdown mode with all circuits shut down except shunt regulator.
SYNC/EN = HIGH: All circuits active with oscillator frequency set by RTCT network.
SYNC/EN = CLOCKED: All circuits active with oscillator frequency set by SYNC clock input. Conversion
cycles initiate on the rising edge of external clock input. The frequency programmed by R19/C33 must be
10% lower than the input SYNC/EN signal frequency.
C Serial Data Input/Output
C Serial Clock Input
CSS
.
FUNCTION
Pin Description
CC
to