APD192G0640001S51 Vishay, APD192G0640001S51 Datasheet - Page 2

• Manufacturer Part Number: APD192G0640001S51
• Description: Plasma Displays 192x64 Module with power supply
• Manufacturer: Vishay
• Type: Drive/ DC Converterr

Specifications of APD192G0640001S51

• Description/function: Provides superior viewing angles
• Viewing Angle: 150 deg
• Viewing Area (w X H): 389.38 mm x 129.29 mm
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

Document Number: 37013
Revision 05-Dec-00
DESCRIPTION OF INPUT SIGNALS
DOT CLOCK - This signal enters the SERIAL DATA on each
low to high transition. A total of 192 DOT CLOCK transitions
must be present for each line of column/anode data.
SERIAL DATA - This signal presents the pixel data in
positive logic format. A logic one represents a lit pixel and a
logic zero represents an extinguished pixel. Data is entered
from right to left. The first pixel data entered will represent
the leftmost pixel in the row.
COLUMN LATCH - This signal latches the pixel data into the
driver outputs. When the COLUMN LATCH signal goes to
logic one the data entered previously will fall through to the
driver outputs. When the signal returns to a logic zero, the
data is latched and the shift register is now ready to accept
the next row of data. Must be held low while entering new
SERIAL DATA.
DISPLAY ENABLE - This signal enables the output drivers.
Using a duty cycle control, this signal may also be used for
intensity control. The DISPLAY ENABLE must be at logic
zero before the COLUMN LATCH signal transitions. To
avoid display blurring, the ROW CLOCK signal should also
transition while DISPLAY ENABLE is a logic zero. It is
recommended that this signal remain low for 10µS min.
ROW DATA - This signal is the first line marker for the scan.
This input should be held high to correspond to the first row
of pixel data.
P3, POWER CONNECTOR
AMP #641737-1 or equivalent.
(Mates with AMP 1-480424-0 or equivalent.)
P2, DATA CONNECTOR
AMP #103309-2 or equivalent.
(Mates with AMP 746195-2, MOLEX 39-27-1146 or equivalent.)
PIN
1
3
5
7
9
11
13
PIN DESCRIPTION
PIN
4
3
2
1
ORDERING INFORMATION
Display Module with Drivers, TTL Interface and On Board DC Converter ...................................................................... APD-192G064-1
Data Connector Kit ................................................................................................................................................................... 280105-05
Power Connector Kit ................................................................................................................................................................. 280108-13
Video Controller (+5V)
Video Contoller (+ 12V)............................................................................................................................................. ............ PDS-500-1
DESCRIPTION
DISPLAY ENABLE
ROW DATA
ROW CLOCK
COLUMN LATCH
DOT CLOCK
SERIAL DATA
No connect
SIGNAL
N/C
GND
GND
VDC
........................................................................................................................................... .................. PDS-500
PIN
10
12
14
2
4
6
8
DESCRIPTION
Reserved
Ground
Ground
DC Converter Supply
DESCRIPTION
GROUND
GROUND
GROUND
GROUND
GROUND
GROUND
GROUND
ROW CLOCK - This signal clocks ROW DATA on the falling
edge. The ROW CLOCK signal is repetitive and must be
present for proper scanning of the display module.
The APD-192G064-1 has a unique input protection circuit
that assures the column drivers stay blanked on power up.
The protection circuit unblanks the column drivers when the
ROW CLOCK signal begins (i.e. the display begins scan-
ning).
Row Data
Display Enable
Row Clock
Column Latch
Dot Clock
PARAMETER
LOGIC AND DATA TIMING
Row Clock
Display Enable
Serial Data
t
t
t
t
t
t
t
1
2
3
4
5
6
7
t
1
1st Bit of Row Will Appear in Leftmost Column
MINIMUM
0
t
6
t
0
5
0
100
25
75
75
—
5
1
1
1
1
Positive Edge x 192
2
t
2
2
2
TYPICAL
70
—
—
—
—
—
—
APD-192G064-1
t
t
4
3
190
62
MAXIMUM
191
62
Vishay Dale
200
t
—
—
—
—
—
—
63
7
63
www.vishay.com
0
0
UNITS
1
nS
uS
uS
Hz
nS
nS
nS
1
3