LQ070Y3DG3B Sharp Microelectronics, LQ070Y3DG3B Datasheet

Page 1

... Technical Document LCD Specification LCD Group LQ070Y3DG3B LCD Module Product Specification March 2009 WVGA Module featuring LED backlight, touch panel, 16:9 aspect ratio, excellent color rendition, 280 nits brightness, and 300:1 contrast. Full Specifications Listing ...

Page 2

...

Page 3

... LQ070Y3DG3B ^SPEC No. DATE LD-21305A Mar.11.2009 RECORDS OF REVISION REVISED No. PAGE - - SUMMARY NOTE st 1 Issue ...

Page 4

These specification sheets are the proprietary product of SHARP CORPORATION(”SHARP) and include materials protected under copyright of SHARP. Do not reproduce or cause any third party to reproduce them in any form or by any means, electronic or mechanical, for ...

Page 5

Table of contents 1. Application ..............................................................................3 2. Overview ................................................................................3 3. Mechanical Specifications ...................................................................3 4. Input Terminals ...........................................................................4 4-1. TFT-LCD panel driving .................................................................4 4-2. LED Backlight driving ..................................................................4 4-3. Touch panel driving ....................................................................5 5. Absolute Maximum Ratings .................................................................5 6. Electrical Characteristics ...

Page 6

... Application This specification applies to a color TFT-LCD module, LQ070Y3DG3B. 2. Overview This module is a color active matrix LCD module incorporating amorphous silicon TFT (Thin Film Transistor composed of a color TFT-LCD panel, driver ICs, power supply circuit, a backlight unit, and a touch panel. Graphics and texts can be displayed on a 800× ...

Page 7

Input Terminals 4-1. TFT-LCD panel driving (Timing signal,DATA signals and +3.3V DC power supply) Pin No. Symbol GND 1 GND 2 VCC +3.3V Power Supply 3 VCC +3.3V Power Supply 4 R0 RED data signal(LSB ...

Page 8

Touch panel driving Pin No. Symbol Recommendation connector : FH19C-4S-0.5SH (Hirose) 5. Absolute Maximum Ratings Parameter Input voltage +3.3V supply voltage LED forward current LED reverse voltage Storage temperature Operating temperature ...

Page 9

On-off conditions for supply voltage 0.9Vcc 0.1Vcc Vcc t2 t1 Signal (LVDS interface) Backlight Symbol for the power sequence for backlight recommended to apply above mentioned ...

Page 10

Interface block diagram of the LCD R 0∼ 0∼ 0∼ Ｖ Ｃ Ｃ 6-2. Backlight driving The backlight system is edge-lighting type with 24 ...

Page 11

Touch panel characteristics Parameter Input voltage Resistor between terminals (TP_X1-TP_X2) Resistor between terminals (TP_Y1-TP_Y2) Line linearity(X direction) Line linearity(Y direction) Insuration resistance Minimum tension for detecting Chattering [Note 1] Wiring diagram of touch panel 8. Timing Characteristics of Input ...

Page 12

Display position Characteristics DEN Setup time Pulse width Phase difference of HSYNC - DEN [Note] (Horizontal display direction) When “DEN” signal is fixed low, 215 clocks are counted from Hsync negative edge and data from after are available. If ...

Page 13

THp Horizontal sync. signal (Hsync) THc Only when “DEN” terminal is fixed "Low" Clock signal (DOTCLK) C1* C215* C216* Number of ...

Page 14

Input Signals, Basic Display Colors and Gray Scale of Each Color Colors & Gray Gray scale Scale Black − Blue − Green − Cyan ...

Page 15

Optical Characteristics Parameter Symbol Horizontal θ21,θ22 Viewing θ11 angle range Vertical θ12 Contrast ratio CRn Response time τr+τd x Chromaticity of white y x Chromaticity of red y x Chromaticity of green y x Chromaticity of blue y Luminance ...

Page 16

Definitions of viewing angle range: [Note 4] Definition of contrast ratio: The contrast ratio is defined as the following. Contrast Ratio (CR) ＝ [Note 5] Definition of response time: The response time is defined as the following figure ...

Page 17

Handling Precautions a) Be sure to turn off the power supply when inserting or disconnecting the cable. Please insert for too much stress not to join FFC/FPC in case of insertion of FFC/FPC sure to design the ...

Page 18

Design guidances for touch panel (T/P) a) Example of housing design (1) Keep the gap (over 0.5mm) between the housing-bezel-edge and T/P surface, to avoid the contact. (See the figure above ) Otherwsie, a “short” with bottom Electrode layer ...

Page 19

Packing form Piling number of cartons Package quantity in one carton Carton size Total mass of one carton filled with full modules 11.4 kg Packing form 15. Reliability Test Items No. Test item 1 High temperature operation test 2 ...

Page 20

Label 1) Module label: Notation: ① Model No. ② Serial No. Ｌ Ｑ ０ ７ ０ Ｙ ３ Ｄ Ｇ ３ Ｂ Details of Serial No ９ ４ ０ ０ ０ ０ ０ １ (Example) Production year(9∼) Production Month(1∼9,X,Y,Z) ...

Page 21

Storage conditions <Environmental condition range of storage temperature and humidity> Temperature degrees Celsius Relative humidity 70% and below Direct sun light Please keep the product in a dark room or cover the product to protect from ...

Page 22

Fig 2. Packing form LD21305A-19 ...

Page 23

Fig3. Outline demensions LD21305A-20 ...

Page 24

... Technical Document LCD Specification LCD Group NORTH AMERICA Sharp Microelectronics of the Americas 5700 NW Pacific Rim Blvd. Camas, WA 98607, U.S.A. Phone: (1) 360-834-2500 Fax: (1) 360-834-8903 www.sharpsma.com TAIWAN Sharp Electronic Components (Taiwan) Corporation 8F-A, No. 16, Sec. 4, Nanking E. Rd. Taipei, Taiwan, Republic of China Phone: (886) 2-2577-7341 ...