LQ104V1DG62 Sharp Microelectronics, LQ104V1DG62 Datasheet
LQ104V1DG62
Specifications of LQ104V1DG62
Available stocks
Related parts for LQ104V1DG62
LQ104V1DG62 Summary of contents
Page 1
... MODEL No. The technical literature is subject to change without notice. So, please contact SHARP or its representative before designing your product based on this literature. MOBILE LIQUID CRYSTAL DISPLY GROUP LITERATURE FOR LQ104V1DG62 Engineering department Mobile LCD Division Ⅲ SHARP CORPORATION LD – 19659A No. DATE JUL．10．2007 ...
Page 2
RECORDS OF REVISION LQ150X1LG81 SPEC No. DATE LD-19659A JUL.10.2007 REVISED No. PAGE - - SUMMARY - 1st Issue NOTE ...
Page 3
... Application This specification applies to color 10.4VGA TFT-LCD module, LQ104V1DG62. These technical literature sheets are the proprietary product of SHARP CORPORATION (”SHARP) and include materials protected under copyright of SHARP. Do not reproduce or cause any third party to reproduce them in any form or by any means, electronic or mechanical, for any purpose, in whole or in part, without the express written permission of SHARP ...
Page 4
Outline specification. Parameter Display size Active area Pixel format Number of colors (Number of gray scale level) Pixel pitch Pixel configuration Display mode Unit outline dimensions *1 Mass Surface treatment *1: Note: excluding back light cables (The backlight cable ...
Page 5
Input Terminals 4-1. TFT-LCD panel driving CN1 Used connector: DF9MA-31P-1V(32 CN1 pin arrangement from module surface (Transparent view) Pin No. Symbol 1 GND 2 CK Clock signal for sampling each data signal 3 Hsync Horizontal synchronous signal ...
Page 6
R/L = High, U/D = Low R/L = High, U/D = High 4-2. Backlight driving CN2 Used connector : SM04B-SRSS-TB(LF)(SN) (JST) Corresponding connector : SHR-04V-S-B (JST) Pin no. symbol 1 V1LOW 2 V1HIGH 3 V2HIGH 4 V2LOW ...
Page 7
Recommended operation condition Parameter Symbol Input voltage V V Supply voltage Ambient temperature Topa [Note1]CK,R0∼R5,G0∼G5,B0∼B5,Hsync,Vsync,ENAB,R/L,U/D [Note2] Vcc-turn-on conditions 0<t1≦15ms 0<t2≦10ms 0<t3≦100ms 0<t4≦1s t5>200ms Vcc-dip conditions 1) 2.5V≦Vcc td≦10ms 2) Vcc<2.5V Vcc-dip conditions should also follow the Vcc-turn-on conditions [Note3] ...
Page 8
Electrical Characteristics 7-1. TFT-LCD panel driving Parameter Current dissipation Vcc=3.3V Vcc=5.0V Permissive input ripple voltage Input voltage Input voltage Input current 1 Low(VI=0V) Hogh(VI=Vcc) Input current 2 Low(VI=0V) Hogh(VI=Vcc) Input current 3 Low(VI=0V) Hogh(VI=Vcc) [Note1] Typical current situation : ...
Page 9
Backlight driving The backlight system is an edge-lighting type with white-LED. The characteristics of LED are shown in the following table. (It is usually required to measure under the following condition. condition:If=130mA,Ta=25℃±2℃) Parameter LED voltage LED current range Number ...
Page 10
When ENAB is fixed "Low", the display starts from the data of C104(clock) as shown in Fig.2. Be careful that the module does not work when ENAB is fixed "High". When the phase difference is below 104 clock, keep ...
Page 11
THp THc * Only when enable terminal is fixed “LOW” ...
Page 12
Input Signals, Basic Display Colors and Gray Scale of Each Color Colors & Gray scale Gray Scale Black 0 0 − ...
Page 13
Optical Characteristics Parameter Viewing Horizontal θ21, θ22 angle Vertical range Contrast ratio Response Rise time Decay Chromaticity of white Chromaticity of red Chromaticity of green Chromaticity of blue Luminance of white White Uniformity [Note] The measurement shall be executed ...
Page 14
Definitions of viewing angle range: [Note2] Definition of contrast ratio: The contrast ratio is defined as the following. Contrast Ratio (CR) = [Note3] Definition of response time: The response time is defined as the following figure and shall be ...
Page 15
Precautions a) Be sure to turn off the power supply when inserting or disconnecting the cable sure to design the cabinet so that the module can be installed without any extra stress such as warp or twist. ...
Page 16
Packing form Product countries / Areas Piling number of cartons Package quantity in one carton Carton size Total mass of one carton filled with full modules Packing form is shown 14.Reliability test items No. Test item 1 High temperature ...
Page 17
... Serial No. (5 digits) Assembly site code Discernment code Production month (1-9X Model number LQ104V1DG62 Lot number (DATE) Quantity of module １０ ｐｃｓ Internal Use Only Ｒ. Ｃ. Product countries / Areas Japan MADE IN JAPAN Taiwan ...
Page 18
...