NHD-4.3-480272ZF-ATXI#-T-1 Newhaven Display, NHD-4.3-480272ZF-ATXI#-T-1 Datasheet - Page 22

• Manufacturer Part Number: NHD-4.3-480272ZF-ATXI#-T-1
• Description: TFT Displays & Accessories 4.3 480 x 272 DPI w/ Touch Panel
• Manufacturer: Newhaven Display

Specifications of NHD-4.3-480272ZF-ATXI#-T-1

• Diagonal: 4.3 in
• Maximum Operating Temperature: + 60 C
• Minimum Operating Temperature: - 20 C
• Operating Current: 50 mA
• Operating Temperature Range: - 20 C to + 60 C
• Product: Displays
• Supply Voltage: 3.3 V
• Touch Panel: Touch Panel
• Viewing Area (w X H): 95.04 mm x 53.86 mm
• Pixel Density: 480 X 282
• Module Size (w X H X T): 105.5 mm x 67.2 mm x 3.8 mm
• Backlighting: White LED
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

STANDARD
(4) When using an electric screwdriver to attach LCM, the screwdriver should be of ground potentiality to minimize as much as
DOC.
(5) Except for soldering the interface, do not make any alterations or modifications with a soldering iron.
(6) Do not drop, bend or twist LCM. In particular, do not forcibly pull or bend the I O cable or the backlight cable.
(7) In order to avoid the cracking of the FPC,you should to pay attention to the area of FPC where the FPC was bent .the edge
(2) Before remove LCM from its packing case or incorporating it into a set, be sure the module and your body have the same
(5) As far as possible make the electric potential of your work clothes and that of the work bench the ground potential.
(6) To reduce the generation of static electricity be careful that the air in the work is not too dried. A relative humidity of
(4) Response time is greatly delayed at temperature below the operating temperature range. However, this does not mean the
(7) When turning the power on, input each signal after the positive/negative voltage becomes stable.
(1) Do not alter, modify or change the the shape of the tab on the metal frame.
(2) Do not make extra holes on the printed circuit board, modify its shape or change the positions of components to be
(3) Do not damage or modify the pattern writing on the printed circuit board.
(4) Absolutely do not modify the zebra rubber strip (conductive rubber) or heat seal connector.
(1) Make certain that you are grounded when handing LCM. To minimize the performance degradation of the LCD modules
(3) When soldering the terminal of LCM, make certain the AC power source for the soldering iron does not leak.
(1) Viewing angle varies with the change of liquid crystal driving voltage (VO). Adjust VO to show the best contrast.
(2) Driving the LCD in the voltage above the limit shortens its life.
(3) If the LCD modules have been operating for a long time showing the same display patterns, the display patterns may
(5) If the display area is pushed hard during operation, the display will become abnormal. However, it will return to normal if it is
(6) Condensation on terminals can cause an electrochemical reaction disrupting the terminal circuit. Therefore, it must be used
of coverlay;the area of surface of Ni-Au plating,the area of soldering land,the area of through hole.
attached.
ordinary CMOS IC.
resulting from destruction caused by static electricity etc., exercise care to avoid holding the following sections when handling
the modules. - Exposed area of the printed circuit board. - Terminal electrode sections.
electric potential.
50%-60% is recommended.
remain on the screen as ghost images and a slight contrast irregularity may also appear. A normal operating status can be
regained by suspending use for some time. It should be noted that this phenomenon does not adversely affect performance
reliability.
LCD will be out of the order. It will recover when it returns to the specified temperature range.
turned off and then back on.
under the relative condition of 40 C , 50% RH.
possible any transmission of electromagnetic waves produced sparks coming from the commutator of the motor.
Since this module uses a CMOS LSI, the same careful attention should be paid to electrostatic discharge as for an
PRODUCT
SPEC.
MODULE
NO.
PAGE
21