ZHX1010MV115THTR Zilog, ZHX1010MV115THTR Datasheet
ZHX1010MV115THTR
Specifications of ZHX1010MV115THTR
Available stocks
Related parts for ZHX1010MV115THTR
ZHX1010MV115THTR Summary of contents
Page 1
... ZHX1010 SIR Transceiver Product Specification PS015105-0702 ZiLOG Worldwide Headquarters • 532 Race Street • San Jose, CA 95126-3432 Telephone: 408.558.8500 • Fax: 408.558.8300 • www.ZiLOG.com ...
Page 2
... San Jose, CA 95126-3432 Telephone: 408.558.8500 Fax: 408.558.8300 www.ZiLOG.com ZiLOG is a registered trademark of ZiLOG Inc. in the United States and in other countries. All other products and/or service names mentioned herein may be trademarks of the companies with which they are associated. Document Disclaimer ©2002 by ZiLOG, Inc. All rights reserved. Information in this publication concerning the devices, applications, or technology described is intended to suggest possible uses and may be superseded ...
Page 3
Table of Contents Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ...
Page 4
List of Figures Figure 1. Application Block Diagrams . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ...
Page 5
... PIN photodiode detector, a digital AC coupled IRED driver, and a receiver/decoder with noise discrimination circuitry in a single, miniature package. The ZiLOG ZHX1010 SIR transceiver provides an efficient implementation of the IrDA-Data standard in a small footprint format. Application circuit space is also minimized, as only two external resistors and one capacitor are needed to com- plete the IrDA transceiver solution ...
Page 6
Pin Descriptions The ZHX1010 SIR transceiver uses the pins listed in Table 1. The pins are described in this section. Table 1. Pin Out for the ZHX1010 SIR Transceiver Pin Name 1 LEDA 2 TXD 3 RXD ...
Page 7
This input has an internal pull-down resistor that is disabled (open-circuited) during shutdown. TXD has integrated digital AC coupling that prevents inadvertent “always on” IREDs; therefore, no external AC coupling components are required for input signals between GND and V ...
Page 8
Recommended Application Circuit Figure 1 shows applications for the ZHX1010 SIR transceiver. Figure 1. Application Block Diagrams PS015105-0702 ZHX1010 SIR Transceiver 4 ...
Page 9
Electrical and Timing Specifications Table 2 through Table 4 present the electrical and timing specifications for the ZHX1010 SIR transceiver. Table 2. Absolute Maximum Ratings Parameter Supply Voltage Power Dissipation Junction Temperature Storage Temperature Solder Temperature (10 seconds) IRED Current ...
Page 10
Table 4. Electrical Characteristics (Continued) Parameter Optical Rise/Fall time Peak Wavelength Optical Overshoot Receiver Detection Threshold Irradiance Overload Irradiance Sunlight Ambient Rejection Digital Input/Output Input High (Logic 1) Voltage Input Low (Logic 0) Voltage Output High ...
Page 11
Transceiver Performance Figure 2 and Figure 3 show the performance of the ZHX1010 SIR transceiver VCC = 2.7V 20 VCC = 3V VCC = 3.3V 10 IrDA Spec Figure ...
Page 12
Mechanical Drawings Figure 4 shows the mechanical drawings for the ZHX1010 SIR transceiver. Figure 4. ZHX1010 Mechanical Drawing PS015105-0702 ZHX1010 SIR Transceiver 8 ...
Page 13
ZHX1010 Soldering and Cleaning Recommendations Follow these recommendations to maintain the performance of the ZHX1010 SIR transceiver. Reflow Soldering • Reflow soldering paste is recommended: Melting temperature: 178 °C ~ 192 °C Composition: Sn 63%, Pb 37% • The recommended ...
Page 14
Cleaning Perform cleaning after soldering under the following conditions: • Cleaning agent: Alcohol • Temperature and time: 30 seconds below 50 ° minutes below 30 °C • Ultrasonic cleaning: Below 20 W ZHX1010 Packing, Storage, and Baking Recommendations ...
Page 15
Moisture Prevention Guidelines In order to avoid moisture absorption during transportation and storage, ZHX1010 reels are packed in aluminum envelopes (see Figure 6) that contain a desiccant with a humidity indicator. While this packaging is an impediment to moisture absorption, ...
Page 16
Taping Specifications Figure 7 and Figure 8 show the reel dimensions and tape dimensions and config- uration for the ZHX1010. LABEL PASTED HERE Figure 7. ZHX1010 Reel Dimensions (Unit: mm) PS015105-0702 SIR Transceiver 330 DIA. DETAIL 2.3 R 1.0 21.5 ...
Page 17
... MIN) Figure 8. ZHX1010 Tape Dimensions and Configuration (Unit: mm) Ordering Information To order ZHX1010 (formerly Calibre CHX1010), use ZiLOG part number ZHX1010MV115THTR. Notes: In order to ensure the lowest possible lead times, ZiLOG uses two different fab sources for the transceiver IC. Both of these ICs have been extensively tested and qualified to meet the ZHX1010 SIR transceiver specifications ...
Page 18
... If you experience any problems while operating the ZHX1010 SIR transceiver you note any inaccuracies while reading this product specification, please copy and complete this form, then mail or fax it to ZiLOG (see “Return Information,” below). We also welcome your suggestions! Customer Information ...