GP1UF310YP0F Sharp Microelectronics, GP1UF310YP0F Datasheet

Page 1

... Features 1. Low power dissipation with no light input (270 µA TYP.) 2. Self-protected against static electricity 3. Four parts, offering a number of center frequencies: Center Bandpass Part Number Frequency (TYP.) GP1UF310YP0F 36 kHz GP1UF311YP0F 38 kHz GP1UF312YP0F 36.7 kHz GP1UF314YP0F 40 kHz Notice The content of this Data Sheet is subject to change without prior notice. ...

Page 2

... A*: 0.15 mm MAX. Coplanarity 5. : ±10° MAX. Preliminary 0.1 MAX. 2.4 4.8 0.1 MAX. Model Number, Lot Number 1.6 4.8 2 GP1UF31xYP0F Series 1.1 7 0.35 2 Mark Model Number GP1UF310YP0F G1 GP1UF311YP0F 1 G2 GP1UF312YP0F G4 GP1UF314YP0F 2 7 Year (2007: Month ( Lot No. (Serial number) No. Pin Name 1 GND Vout 5 Vcc NC ...

Page 3

Block Diagram Amp Limiter GP1UF31YP0F-7 ■ Absolute Maximum Ratings Parameter Symbol Supply voltage V CC Operating temperature Topr Storage temperature Tstg Soldering temperature Tsol 1 Non-condensing: humidity kept above dew point Apply heat no more than 10 ...

Page 4

... Output Signal T2 T1 NOTE: Carrier Duty 50% GP1UF31YP0F-8 Preliminary Condition (no light See Note 1 See Figure 2 See Figure 2 GP1UF310YP0F GP1UF311YP0F GP1UF312YP0F GP1UF314YP0F L 4 GP1UF31xYP0F Series Min. Typ. Max. Unit 2.7 5.5 V — 0.27 0.4 mA – 0.5 — — — ...

Page 5

Performance Measurements The parameters in the Characteristics tables were gathered using the transmitter jig in Fig. 2, along with the receiver jig in Fig Linear Reception: Distance between transmitter and receiver: 0.2 to 5.0 meters; detector face ...

Page 6

Design Considerations Design Guidelines 1. This product is not designed to be electromagnetic- and ionized-particle-radiation resistant. 2. Avoid placing mechanical stress upon this part, whether to the case or terminals. Such stresses may crack the molding material, possibly breaking ...

Page 7

Fig. 5. Device Connection GND NC NC Vout C GND Vout GP1UF31YP0F-3 ■ Manufacturing Guidelines ● Storage and Handling 1. Moisture-proofing: These parts are shipped in vacuum-sealed packaging to keep them dry and ready for use. ...

Page 8

Soldering Instructions 1. Sharp recommends soldering this part no more than twice and at the profile shown in Fig. 6. Reflow should occur within three days, after storing at 10°C to 30°C, and at no more than 70% relative ...

Page 9

PCB Footprint Fig. 7 shows the recommended PCB footprint for this device. Fig. 7. Device Footprint Center of Mounting Area 2 0.8 1.1 1.6 0.3 2.4 Avoid circuit runs in this area. GP1UF31YP0F-4 ● Conductive ...

Page 10

Soldering Mask Fig. 9 shows the recommended solder mask for this device. Fig. 9. Soldering Mask 2.8 0.8 0.3 1.6 2.4 NOTES: 1. Units Dimensions are shown for reference = Soldering paste area GP1UF31YP0F-6 ● Cleaning Instructions ...

Page 11

Tape Specifications Fig. 10 Tape Shape and Dimensions 2.0 ±0.10 4.0 8.0 ±0.10 GP1UF31YP0F-12 Preliminary ±0.10 +0.10 1.5 -0.00 2.04 ±0.10 1.23 1.23 ±0.10 ±0.10 11 GP1UF31xYP0F Series 0.33 ±0.05 2.30 ±0.10 Sheet No.: OP06Y11A March 2009 ...

Page 12

Reel Specifications Fig. 11 Reel Shape and Dimensions 2.0 ±0.5 21.0 ±0.8 330.0 ±2.0 GP1UF31YP0F-13 ■ Product Insertion Direction Fig. 12 shows the orientation of the device in the tape. Fig. 12 Product Insertion Label GP1UF31YP0F-14 Preliminary 22.4 ±1.0 ...

Page 13

Packing Information Product is sealed in laminated aluminum bags with 2000 pieces per reel, silica gel desiccant, and humidity telltale. The EIAJ C-3 compliant label is filled out and affixed to the bag. Four of these packaged reels of ...

Page 14

Presence of ODCs (RoHS Compliance) This product shall not contain the following materials, and they are not used in the production process for this product: • Regulated substances: CFCs, Halon, Carbon tetrachloride, 1,1,1-Trichloroethane (Methylchloroform). Specific brominated flame retardants such ...

Page 15

Important Notices · The circuit application examples in this publication are provided to explain representative applications of SHARP devices and are not intended to guarantee any circuit design or license any intellectual property rights. SHARP takes no responsibility for ...