UDW2 3M, UDW2 Datasheet - Page 2

• Manufacturer Part Number: UDW2
• Description: SCOTCHLOK INLINE 4-WIRE 16-19AWG
• Manufacturer: 3M
• Series: Scotchlok™r

Specifications of UDW2

• Terminal Type: Inline, Tap
• Number Of Wire Entries: 4
• Termination: IDC
• Wire Gauge: 16-19 AWG
• Insulation: Fully Insulated
• Features: Gel Filled
• Connector Type: Splice
• Insulator Colour: Black
• Termination Method: Crimp
• Colour: Black
• Insulator Material: Plastic
• Jacket Colour: Black
• Jacket Material: Plastic
• Termination Type: Crimp
• Wire: RoHS Compliant
• Product: Splices
• Stud / Tab Size: # 10
• Gender: Male
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Color: -
• Lead Free Status / Rohs Status: Details
• Other names: 5111519144; 51115191442; 80611316508; UDW2000

1.0 General
The 3M brand Scotchlok
Drop Wire Connector is a full pair
moisture-resistant drop wire connector
(1.3 mm - 0.9 mm) copper or copper-
clad steel conductors with insulation
• Double Headed Drop Wire Clamps
3.01 Flush cut the two ends to be
based on information believed to be reliable, but
guaranteed. Before utilizing the product, the user
liability whatsoever in connection with such use.
especially designed for 16 - 19 AWG
diameters up to .175” (4.4 mm) O.D.
2.0 Accessories Required
• Scotchlok E-9B or E-9BM
3.0 Drop Wire Preparation
3.02 Slit drop wire approximately
Note: On “C Type” drop wire, remove
the outer jacket.
Important N o t i c e
All statements, technical information, and
recommendations related to Seller’s products are
the accuracy or completeness thereof is not
should determine the suitability of the product for
its intended use. The user assumes all risks and
Telecom Systems Division
6801 River Place Blvd.
Austin, TX 78726-9000
800/426 8688
Crimping Tool
(if used mid-span)
spliced.
1 1/4” (32 mm) with a drop wire
splitter.
™
UDW2
76654
76655
3.03 Line up ribs of drop wires so that
3.05 Adjust the E-9B Crimping Tool
Any statements or recommendations of the Seller
which are not contained in the Seller’s current
publications shall have no force or effect unless
contained in an agreement signed by an
authorized officer of Seller. The statements
contained herein are made in lieu of all
warranties, express or implied, including but not
limited to the implied warranties of merchantability
and fitness for a particular purpose which
warranties are hereby expressly disclaimed.
Printed on 50% recycled paper
with 10% post consumer.
3.04 Important: Press both thumbs
tip and ring are not reversed at
the splice. Slide one of the drop
wires into the connector.
Holding connector and drop
wire, insert the other drop wire.
Make sure both drop wires are
inserted all the way.
down equally on the connector
cap. You will hear a “crunch.”
This means the connector is
pre-crimped. (This will help
hold the drop wires in place
until the connector is crimped).
to thin-thin configuration or the
E-9BM Crimping Tool to thick-
thin configuration on the
adjustable jaws of the tool.
Pre-Crimp
76659
766557
76656
3.06 Once the tool is adjusted
Shipping Unit: 100 connectors
SELLER SHALL NOT BE LIABLE TO THE USER
OR ANY OTHER PERSON UNDER ANY LEGAL
CONSEQUENTIAL DAMAGES SUSTAINED OR
INCURRED BY REASON OF THE USE OF ANY
OF THE SELLER’S PRODUCTS THAT WERE
DEFECTIVE.
3.07 When connector is used mid-
Packing: 25/bag, 4 bags/cs.,
THEORY, INCLUDING BUT NOT LIMITED TO
NEGLIGENCE OR STRICT LIABILITY, FOR ANY
INJURY OR FOR ANY DIRECT OR
Printed in USA.
© 3M 1994 80-6107-5732-2
properly, position connector all
the way back in the jaws. Fully
crimp the connector so that the
cap is flush with the body.
span, provide additional strain
relief by using two drop wire
clamps. Make sure that the
clamps are locked onto the drop
wires by tapping the clamps to
set the teeth.
1.1 kg (2.5 lbs.)/cs.
76662
76660