FWFTVC6G Amphenol PCD, FWFTVC6G Datasheet - Page 2

• Manufacturer Part Number: FWFTVC6G
• Description: CAP FW METALLIC FOR PLUG GREEN
• Manufacturer: Amphenol PCD
• Series: FW Field TVr

Specifications of FWFTVC6G

• Accessory Type: Cap (Cover)
• For Use With/related Products: Firewire (IEEE1394) Plug
• For Use With: APC1016 - CONN FIREWIRE PLUGFWFTV6G - CONN FIRE WIRE PLUG GREEN
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

2
Amphenol Pcd
Tel. :+ 1 978-532-8800 x273
Plug Assembly
Receptacle Assembly
(For Solder back-termination Styles only)
1.
2.
3.
4.
5.
6.
7.
Important Note : The sealing of the connector is not done by the
To Solder your cable onto the PCB :
1.
2.
Removing Modules
1.
2.
Main
Main
Data Transmission
•
Data rate
400 Mbits/second over 4.5 meters
Mechanical
•
series III type) with anti-decoupling device
•FW plug retention in the receptacle : 100 N in the axis
•
IEEE 1394a – 2000
Tri-start thread coupling mechanism (MIL-DTL-38999
Mating cycles : 500 to 1500 times
If a fully sealed (IP67) assembly is required: Install the
white tape around the plug to cover the 4 holes of the
overmolding. If there are no holes omit this step.
Insert the black O Ring around the front face of the IEEE
1394 plug. This O Ring will ensure the seal.
Insert the IEEE 1394 cordset into the metallic backshell.
Insert laterally onto the cable the retention spacer (this
spacer is soft so as to adapt to various overmolding styles)
and slide the IEEE 1394 plug into this retention spacer.
Insert the friction ring laterally onto the cable cordset.
Insert the IEEE 1394 plug into the metallic circular shell.
Note at this step that the main key is used for polarization.
Screw the backshell on the plug body. A spanner may be
required to fully close the backshell to the circular shell.
black retention spacers which are sloted, but rather by the
front face O-Ring (Fig 2).
Attach the 2 metallized plastic inserts around the PCB
(Fig 1a & 1b).
Insert the IEEE 1394 module from the rear of the
connector.
Insert the removal tool FWF
ODE from the front
Push the module back with
thumb.
Can be used with most IEEE 1394 cordset brands : No tools required!
Characteristics
Characteristics
– 2 Technology Drive – Peabody – Massachussetts – 01960 USA
Fax : + 1 978-532-680
Assembly Instructions
Environmental Protection
•
minutes)
•
•
•
•
connectors (mated pair)
•
•
Sealing (mated) : IP67 (Temporary immersion - 1M up to 30
Salt Spray :
Fire Retardant / Low Smoke : UL94 V0 and NF F 16 101 & 16 102
Vibrations : 10 – 500 Hz, 10 g, 3 axes : no discontinuity > 1micro s
Shocks : IK06 : weight of 250 g drop from 40 cm [15.75 in] onto
Humidity : 21 days, 43°C, 98% humidity
Temperature Range : - 55°C / +85°C
3
5
7
48 hr with Nickel plating
500 hr with Olive Drab Cadmium
1a
1b
1
Amphenol
6
4
2
2
1
2
®