KME63VB471M12X25LL United Chemi-Con, KME63VB471M12X25LL Datasheet - Page 2

• Manufacturer Part Number: KME63VB471M12X25LL
• Description: CAPACITOR ALUM ELEC, 470UF, 63V
• Manufacturer: United Chemi-Con
• Type: Electrolyticr

Specifications of KME63VB471M12X25LL

• Tolerance (+ Or -): 20%
• Voltage: 63VDC
• Esr: 317mOhm
• Mounting Style: Through Hole
• Construction: Radial
• Dcl: 2uA
• Lifetime: 1000
• Product Diameter (mm): 12.5mm
• Product Height (mm): 25mm
• Product Depth (mm): Not Requiredmm
• Product Length (mm): Not Requiredmm
• Lead Spacing (nom): 5mm
• Lead Diameter (nom): 0.6mm
• Operating Temp Range: -55C to 105C
• Capacitance: 470uF
• Ripple Current: 700mA
• Capacitance Tolerance: ± 20%
• Voltage Rating: 63V
• Lead Spacing: 5mm
• Operating Temperature Range: -55°C To +105°C
• Termination Type: Radial Leaded
• Capacitor Terminals: Radial Leaded
• Rohs Compliant: No
• Lead Free Status / RoHS Status: Not Compliant

KME Series
KME Specifications
Operating Temperature Range
Rated Voltage Range
Capacitance Range
Capacitance Tolerance
Leakage Current
Dissipation Factor ( Tan )
Low Temperature
Characteristics
Ripple Current Multipliers
Refer to Section 4 of the
Mini-Glossary for explanation
of Ripple Current Multipliers.
Load Life
Shelf Life
Others
United Chemi-Con, Inc. 9801 W. Higgins Road, Rosemont, IL 60018 Tel [phone] Fax [phone] www.chemi-con.com
Item
6.3 to 400VDC
0.1 to 15,000 F
At
Where I = Leakage current ( A ), C = Nominal capacitance ( F ) and V = Rated voltage ( V )
At
When nominal capacitance exceeds 1,000 F, add 0.02 to the values above for each 1,000 F increase.
At 120Hz, impedance ( Z ) ratio between the
exceed the values given below.
Ambient Temperature ( C )
Frequency (Hz )
The following specifications shall be satisfied when the capacitors are restored to
after subjecting them to the DC rated voltage for 1,000 hours at 105 C with the rated ripple
current applied. The sum of DC voltage and peak AC voltage must not exceed the full rated
voltage of the capacitors.
Capacitance change: ≤
Tan
Leakage current
The following specifications shall be satisfied when the capacitors are restored to
exposing them for 1,000 hours at 105 C without voltage applied. The rated voltage shall be
applied to the capacitors for a minimum of 30 minutes, at least 24 hours and not more than
48 hours before the measurements.
Capacitance change: ≤
Tan
Leakage current
Satisfies characteristic W of JIS C5141
Rated Voltage ( V )
Tan
Rated Voltage ( V )
Z ( 25 C ) / Z ( 20 C )
Z ( 40 C ) / Z ( 20 C )
55 to 105 C for 6.3 to 100VDC;
20% ( M ) at
DC Rated Voltage
Capacitance ( F )
20 C
20 C, 120Hz
1.75
85 C
( DF )
( DF )
≤ 3.3 F
4.7- 33 F
47-1000 F
≥ 2200 F
6.3 -100V
160 - 400V
( DF )
20 C, 120Hz
1.00
105 C
: ≤ 200% of initial specified value
: ≤ initial specified value
: ≤ 200% of initial specified value
: ≤ initial specified value for 6.3 -100V
: ≤ 500% of initial specified value for 160 - 400V
0.22
After 2 minutes
After 1 minute
After 5 minutes
6.3
6.3
4
8
50Hz
20% of initial measured value
20% of initial measured value
0.65
0.75
0.80
0.85
Test Time
0.19
10
10
3
6
0.16
40 to 105 C for 160 to 400VDC
120Hz
16
1.00
1.00
1.00
1.00
Characteristics
16
2
4
I
CV ≤ 1,000: I
CV ≤ 1,000: I
0.14
0.002CV or 2 A, whichever is greater.
25
25 C or
25
2
3
300Hz
0.12
1.35
1.25
1.15
1.03
35
35
0.1CV 40
0.03CV 15
2
3
0.10
40 C value and
Leakage Current ( A )
50
50
2
3
1kHz
1.75
1.50
1.30
1.05
0.09
63
63 -100
CV >1,000: I
CV >1,000: I
0.08
100
2
3
10kHz
20 C value shall not
2.30
1.75
1.40
1.08
160 - 250
160 - 250
0.20
3
4
0.04CV 100
0.02CV 25
20 C
20 C after
100kHz
350 - 400
350 - 400
2.50
1.80
1.50
1.08
0.24
6
6
151