GCM21B5C1H223JA16L Murata, GCM21B5C1H223JA16L Datasheet - Page 43

• Manufacturer Part Number: GCM21B5C1H223JA16L
• Manufacturer: Murata

Specifications of GCM21B5C1H223JA16L

• Tolerance (+ Or -): 5%
• Voltage: 50VDC
• Temp Coeff (dielectric): C0G
• Operating Temp Range: -55C to 125C
• Mounting Style: Surface Mount
• Construction: SMT Chip
• Case Style: Ceramic Chip
• Failure Rate: Not Required
• Wire Form: Not Required
• Product Length (mm): 2mm
• Product Depth (mm): 1.25mm
• Product Height (mm): 1.25mm
• Product Diameter (mm): Not Requiredmm
• Capacitance: .022uF
• Package / Case: 0805
• Lead Free Status / RoHS Status: Compliant

!Note
• This PDF catalog is downloaded from the website of Murata Manufacturing co., ltd. Therefore, it’s specifications are subject to change or our products in it may be discontinued without advance notice. Please check with our
• This PDF catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
sales representatives or product engineers before ordering.
!Note
No.
Medium Voltage for Automotive GCM Series Low Disspation Factor Specifications and Test Methods
1
2
3
4
5
6
7
8
9
Pre-and Post-Stress
Electrical Test
High Temperature
Exposure (Storage)
Temperature
Cycle
Destructive
Physical Analysis
Moisture
Resistance
Biased Humidity
Operational Life
External Visual
Physical Dimension
• Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.
• This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
AEC-Q200
Test Item
Appearance No marking defects
Capacitance
Change
Q
I.R.
Appearance No marking defects
Capacitance
Change
Q
I.R.
Appearance No marking defects
Capacitance
Change
Q
I.R.
Appearance No marking defects
Capacitance
Change
Q
I.R.
Appearance No marking defects
Capacitance
Change
Q
I.R.
The measured and observed characteristics should satisfy the
specifications in the following table.
Within 2.5% or 0.25pF
(Whichever is larger)
QU1000
More than 10,000M or 500M · F
(Whichever is smaller)
The measured and observed characteristics should satisfy the
specifications in the following table.
Within 2.5% or 0.25pF
(Whichever is larger)
QU1000
More than 10,000M or 500M · F
(Whichever is smaller)
No defects or abnormalities
The measured and observed characteristics should satisfy the
specifications in the following table.
Within 3.0% or 0.3pF
(Whichever is larger)
QU350
More than 10,000M or 500M · F
(Whichever is smaller)
The measured and observed characteristics should satisfy the
specifications in the following table.
Within 3.0% or 0.3pF
(Whichever is larger)
QU200
More than 1,000M or 50M · F
(Whichever is smaller)
The measured and observed characteristics should satisfy the
specifications in the following table.
Within 3.0% or 0.3pF
(Whichever is larger)
QU350
More than 1,000M or 50M · F
(Whichever is smaller)
No defects or abnormalities
Within the specified dimensions
Specifications
–
Sit the capacitor for 1000 12 hours at 150 3 C. Let sit for 24 2
hours at room temperature, then measure.
Fix the capacitor to the supporting jig in the same manner and
under the same conditions as (19). Perform the 1000 cycles
according to the 4 heat treatments listed in the following table.
Let sit for 24 2 hours at room temperature, then measure.
Per EIA-469
Apply the 24 hour heat (25 to 65 C) and humidity (80 to 98%)
treatment shown below, 10 consecutive times.
Let sit for 24 2 hours at room temperature, then measure.
Apply the rated voltage and DC1.3+0.2/-0V (add 6.8k
resistor) at 85 3 C and 80 to 85% humidity for 1000 12 hours.
Remove and let sit for 24 2 hours at room temperature, then
measure.
The charge/discharge current is less than 50mA.
Apply voltage as Table for 1000 12 hours at 125 3 C. Let sit
for 24 2 hours at room temperature, then measure.
The charge/discharge current is less than 50mA.
Visual inspection
Using calipers and micrometers
Specifications and Test Methods
Time (min.)
Temp. ( C)
Rated Voltage
Step
-10
DC250V
DC630V
70
65
60
55
50
45
40
35
30
25
20
15
10
-5
C
5
0
0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24
-55+0/-3
Initial measurement
15 3
1
AEC-Q200 Test Method
Humidity
90-98%
Room Temp.
+10
-2
One cycle 24 hours
150% of the rated voltage
120% of the rated voltage
Humidity
80-98%
C
2
1
Continued on the following page.
Applied Voltage
Humidity
90-98%
Hours
125+3/-0
15 3
3
Humidity
80-98%
Room Temp.
Humidity
90-98%
4
1
C03E.pdf
41
10.5.20
2