EZA-NT16AAAJ Panasonic, EZA-NT16AAAJ Datasheet
EZA-NT16AAAJ
Specifications of EZA-NT16AAAJ
Related parts for EZA-NT16AAAJ
EZA-NT16AAAJ Summary of contents
Page 1
... Takes up less space than discrete chip resistor & chip capacitor EZACT: 0402 inches (1.0 mm EZADT: 0402 inches (1.0 mm EZAST/SS, EZASTB/SSB: 0402 inches (1.0 mm EZANT: 0805 inches (2.0 mm <Effect of high density placing, PWB space saving> RC Low pass fi lter I/O ...
Page 2
... Components 4 2 3.1 mm ✽ available for EZADT, EZAST, and EZANT ✽ and 22 pF available for EZACT 100 pF available for EZAST, EZADT. 220 pF to 1000 pF available for EZANT. ● EZACT EZADT EZASS EZANT (R/C Except the standard Combination) • • • ...
Page 3
... EZADT Alumina substrate Marking GND Electrode (Outer) GND Electrode (Outer) Protective coating Electrode (Outer) EZASTB/SSB Marking Alumina substrate GND Electrode 33 (Outer) GND Electrode (Outer) Protective coating Electrode (Outer) EZADT EZAST/SS EZANT • • GND 1 GND R1=R2=R3=R4 C1=C2=C3=C4 – 263 – Chip RC Networks ...
Page 4
... Chip RC Networks EZADT 0.33±0. 0.20 3.20±0.15 0.65 – 0.10 0.35±0.10 Size : 1206 inches Mass (Weight) [1000 pcs.] :11 g EZANT 0.65±0.20 + 0.20 6.4±0.2 0.80 – 0.10 0.75±0.20 Size : 2512 inches Mass (Weight) [1000 pcs.] : Sep. 2010 ...
Page 5
... Design and specifi cations are each subject to change without notice. Ask factory for the current technical specifi cations before purchase and/or use. Should a safety concern arise regarding this product, please be sure to contact us immediately. EZAC Standard : 100 , 220 , 470 , 1 k EZAD/S/N Standard : 100 , 220 , 470 , Characteristic: +20 %/– ...
Page 6
... Should a safety concern arise regarding this product, please be sure to contact us immediately. Pitch ( φ ±0.20 ±0.05 ±0.10 8.00 3.50 1.75 ±0.10 4.00 ±0.30 ±0.20 ±0.20 12.00 5.50 1.75 Type EZACT EZADT EZAST/SS EZASTB/SSB EZANT – 266 – Chip RC Networks ) Quantity 1 5000 pcs./reel 4000 pcs./reel φD (Only Emboss) 1 φ ...
Page 7
... GND b ●EZASTB/SSB f2 GND ●EZANT • Design to make GND pattern as large as possible, because high frequency noise is removed from GND terminals of chip RC network. Design and specifi cations are each subject to change without notice. Ask factory for the current technical specifi cations before purchase and/or use. ...
Page 8
Recommended Soldering Conditions Recommendations and precautions are described below. ● Recommended soldering conditions for refl ow ·R efl ow soldering shall be performed a maximum of two times. ·Please contact us for additional information when used in conditions other ...
Page 9
Safety Precautions (Common precautions for Fixed Resistors, Noise Suppression Device, ESD Suppressor, fuses, and MR Sensors) • When using our products, no matter what sort of equipment they might be used for, be sure to make a written agreement on ...