CR2A10YLTE470M/101J KOA Speer Electronics, CR2A10YLTE470M/101J Datasheet - Page 3
![no-image](/images/manufacturer_photos/0/3/373/koa_speer_electronics_sml.jpg)
CR2A10YLTE470M/101J
Manufacturer Part Number
CR2A10YLTE470M/101J
Description
Manufacturer
KOA Speer Electronics
Datasheet
1.CR2A10YLTE470M101J.pdf
(3 pages)
Specifications of CR2A10YLTE470M/101J
Capacitance
47pF
Capacitor Tolerance
20%
Resistance
100Ohm
Resistance Tolerance
5%
Number Of Resistors/capacitors
4R/4C
Number Of Terminals
10
Mounting Style
Surface Mount
Construction
SMT Chip
Terminal Pitch
0.8mm
Temperature Coefficient
±200
Product Length (mm)
4mm
Product Depth (mm)
2.1mm
Operating Temp Range
-25C to 85C
Lead Free Status / RoHS Status
Not Compliant
Performance Characteristics
122
Insulation Resistance
Dielectric Withstanding Voltage
Resistance to Solder Heat
Solderability
Terminal Strength
(Bend Test)
Resistance to Solvents
Vibration
Temperature Cycling
Humidity
(No Load)
Moisture Resistance
Load Life
Specifications given herein may be changed at any time without prior notice. Please confirm technical specifications before you order and/or use.
KOA Speer Electronics, Inc. • Bolivar Drive • P .O. Box 547 • Bradford, PA 16701 • USA • 814-362-5536 • Fax: 814-362-8883 • www.koaspeer.com
Parameter
Approximately 95% of the terminal
should be covered with new solder
No evidence of damage
No evidence of damage
No evidence of damage
No evidence of damage
No evidence of damage
No evidence of damage
No evidence of flaming,
No mechanical damage
No mechanical damage
I.R. more than 100 MΩ
I.R. more than 100 MΩ
I.R. more than 100 MΩ
I.R. more than 100 MΩ
I.R. more than 100 MΩ
fuming or breakdown
More than 10
∆C within ±20%
∆C within ±20%
∆C within ±20%
∆C within ±20%
∆C within ±20%
∆R within ±5%
∆R within ±5%
∆R within ±5%
∆R within ±5%
∆R within ±5%
Requirement
D.F. within 5%
D.F. within 5%
D.F. within 5%
D.F. within 5%
D.F. within 5%
3
MΩ
(continued)
Within 2 minutes at DC 25V between terminal and another
2.5 times maximum rated voltage for 5 seconds with 50 mA maximum
charging current
Immerse in solder (H63A) @ 260° ± 5°C for 10 seconds ± 1 second
Measurement shall be done 24 hours ± 4 hours @ room condition after test.
Immerse in solder (H63A) @ 235° ± 5°C for 3 seconds ± 0.5 second
Specimen shall be soldered on PCB and support by applying strength
so that the bending width becomes 3mm
Immerse in the IPA @ 20°C to 25°C for 60 seconds ± 10 seconds
2 hours in each direction of X, Y, Z on PCB at a frequency range
of 10 - 55 - 10Hz with 1.5mm amplitude. Measurement shall be done
24 hours ± 4 hours @ room condition after test.
100 cycles between -25°C/30 minutes and +85°C/30 minutes
Measurement shall be done 24 hours ± 4 hours @ room condition after test.
MIL-STD-202F, Method 106, 10 cycles
Measurement shall be done 24 hours ± 4 hours @ room condition after test.
40°C ± 2°C, 90 - 95% RH, 500 hours
Capacitor: DC 25V, 500 hr ON
Resistor: Rated working voltage, 1.5 hr ON, 0.5 hr OFF
Measurement of capacitor shall be done 24 hours ± 4 hours
@ nominal condition after test.
85°C ± 2°C, 1000 hours
Capacitor: DC 25V, 1000 hr ON
Resistor: Rated working voltage, 1.5 hr ON, 0.5 hr OFF
Measurement of capacitor shall be done 24 hours ± 4 hours
@ nominal condition after test.
Test Method
v
v
11/01/03