TZB4R500CA10B00 Murata, TZB4R500CA10B00 Datasheet - Page 8
![](/photos/30/41/304127/tzb4_c_sml.jpg)
TZB4R500CA10B00
Manufacturer Part Number
TZB4R500CA10B00
Description
Manufacturer
Murata
Type
Ceramicr
Datasheet
1.TZB4R500CA10B00.pdf
(45 pages)
Specifications of TZB4R500CA10B00
Capacitance Range (min/max) (pf)
7/50
Tolerance (+ Or -)
0% to 100%
Voltage
50VDC
Temp Coeff (dielectric)
N750±300 ppm/°C
Operating Temp Range
-25C to 85C
Mounting Style
Through Hole
Construction
Top Adj
Q
300
Failure Rate
Not Required
Product Length (mm)
4.5mm
Product Depth (mm)
4mm
Product Height (mm)
3mm
Product Diameter (mm)
Not Requiredmm
Lead Free Status / RoHS Status
Compliant
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
TZB4R500CA10B00
Manufacturer:
MURATA
Quantity:
240 000
!Note
• This PDF catalog is downloaded from the website of Murata Manufacturing co., ltd. Therefore, it’s specifications are subject to change or our products in it may be discontinued without advance notice. Please check with our
• This PDF catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
sales representatives or product engineers before ordering.
!Note
1. Soldering
1. Use suitable screwdrivers that fit comfortably in
2. When adjusting with a screwdriver, do not apply
Before using trimmer capacitor, please test after
assembly in your particular mass production system.
(1) TZR1 series can be soldered by reflow soldering
(2) Soldering condition
(3) The amount of solder is critical.
(4) The thickness of solder paste should be printed
(5) When using soldering iron, the diameter of the
Notice (Soldering and Mounting)
Notice (Handling)
driver slot.
excessive force (preferably 0.5 N [Ref: 50gf] max.)
to minimize capacitance drift. If excessive force
is applied to the screwdriver slot, it may cause
deformation of the products.
Notice (Other)
*Recommended screwdriver for manual adjustment
method and soldering iron. Do not use flow
soldering method (dipping).
Refer to the temperature profile.
If the soldering conditions are not suitable, e.g.,
excessive time and/or excessive temperature, the
trimmer capacitor may deviate from the specified
characteristics.
from 100 micro m to 150 micro m and the dimension
of land pattern should be Murata's standard land
pattern used at reflow soldering.
Insufficient amounts of solder can lead to
insufficient soldering strength on PCB.
Excessive amounts of solder may cause bridging
between the terminals or contact failure due to
flux wicking up.
string solder shall be less than 0.5mm. The
string solder shall be applied to the lower
part of the terminal only. Do not apply flux
except to the terminals. Excessive amounts of
solder and/or applying solder to the upper part
of the terminal may cause fixed metal rotor or
contact failure due to flux invasion into
• Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.
• This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
MURATA: KMDR160
2. Mounting
3. Do not apply adhesive, lock paints, or any other
3. Cleaning
4. Other
(6) Our recommended chlorine content of solder is
(7) Do not use water-soluble flux (for water
(1) Do not apply excessive force (preferably 5.0 N
(2) Do not warp and/or bend PCB to prevent trimmer
(3) Use the suitable dimension of the pick-up nozzle.
substances to the trimmer capacitor to secure the
rotor position. They may cause corrosion or
electrical contact problems.
Cannot be cleaned because of open construction.
Note the polarity of the trimmer capacitor to
minimize influence by stray capacitance.
(Refer to the dimensions concerning the polarity.)
(a) Solder paste: 0.2wt% max.
(b) String solder: 0.5wt% max.
the movable part and/or the contact point. The
soldering iron should not come in contact with
the monolithic stator of the trimmer capacitor.
If such contact does occur, the trimmer
capacitor may be damaged.
as follows.
cleaning). To prevent the deterioration of
trimmer capacitor characteristics, apply flux
only to terminals.
[Ref: 500gf] max.), when the trimmer capacitor
is mounted on the PCB.
capacitor from breaking.
(1.1-1.2mm external diameter and 0.8-0.9mm bore
diameter.)
T13E.pdf
7
07.3.1
1