CRCW12060000ZSTA Vishay, CRCW12060000ZSTA Datasheet - Page 6
![RESISTOR, CHIP, JUMPER, ZERO OHM, 250mW](/photos/30/47/304787/dcrcw_sml.jpg)
CRCW12060000ZSTA
Manufacturer Part Number
CRCW12060000ZSTA
Description
RESISTOR, CHIP, JUMPER, ZERO OHM, 250mW
Manufacturer
Vishay
Type
Thick Filmr
Series
CRCWr
Specifications of CRCW12060000ZSTA
Resistance
0Ohm
Temperature Coefficient
Not Required
Power Rating(s)
Not RequiredW
Tolerance (+ Or -)
Not Required
Mounting Style
Surface Mount
Package / Case
1206
Operating Temp Range
-55C to 155C
Case Style
Molded
Military Standard
Not Required
Failure Rate
Not Required
Product Length (mm)
3.2mm
Product Depth (mm)
1.6mm
Product Height (mm)
0.55mm
Power Rating
250mW
Voltage Rating
200V
Resistor Element Material
Thick Film
Resistor Case Style
1206
No. Of Pins
2
Lead Free Status / RoHS Status
Not Compliant
D/CRCW e3
Vishay
www.vishay.com
130
THE PRODUCT DESCRIBED HEREIN AND THIS DATASHEET ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT
TEST PROCEDURES AND REQUIREMENTS
EN
60115-1
CLAUSE
4.5
4.7
4.13
4.17.2
4.8.4.2
4.32
4.33
4.19
4.23
4.23.2
4.23.3
4.23.4
4.23.5
4.23.6
4.23.7
4.25.1
METHOD
60068-2
21 (Uu
21 (Uu
14 (Na)
30 (Db)
30 (Db)
58 (Td)
13 (M)
2 (Ba)
1 (Aa)
TEST
IEC
-
-
-
-
-
-
-
3
1
)
)
Short time overload
Substrate bending
Climatic sequence:
Rapid change of
Damp heat, cyclic
Damp heat, cyclic
Low air pressure
Voltage proof
Temperature
Solderability
temperature
Resistance
Endurance
(adhesion)
coefficient
DC load
at 70 °C
Dry heat
Shear
TEST
Cold
For technical questions, contact:
Standard Thick Film Chip Resistors
Stability for product types:
RR 1608 and smaller: 9 N
RR 2012 and larger: 45 N
This datasheet is subject to change without notice.
1 kPa; (25 ± 10) °C; 1 h
U =
duration: Acc. to style
Solder bath method;
Solder bath method;
U = 2.5 x
(20/- 55/20) C and
U = 1.4 x U
non activated flux;
non-activated flux;
30 min. at - 55 °C;
55 °C; 90 % RH;
55 °C; 90 % RH;
1.5 h on; 0.5 h off;
30 min. at 125 °C
Sn96.5Ag3Cu0.5
(20/125/20) C
PROCEDURE
U =
24 h; 5 cycles
70 °C; 1000 h
70 °C; 8000 h
Depth 2 mm;
125 °C; 16 h
24 h; 1 cycle
(235 ± 5) °C
(245 ± 5) C
1000 cycles
2 x U
- 55 °C; 2 h
P
Sn60Pb40
(2 ± 0.2) s
(3 ± 0.3) s
5 cycles
70
3 times
P
x R
D/CRCW e3
-
-
70
P
max.
ins
70
x R
U
; 60 s
;
x R
max.
;
thickfilmchip@vishay.com
±0.25 % R + 0.05)
± (0.25 % R + 0.05 )
± (1 % R + 0.05 )
± (1 % R + 0.05 )
± (1 % R + 0.05 )
± (2 % R + 0.1 )
No visible damage, no open circuit in bent position
OR BETTER
± 100 ppm/K
STABILITY
CLASS 1
± 1 %
PERMISSIBLE CHANGE (R)
Good tinning ( 95 % covered)
Good tinning ( 95 % covered)
No flashover or breakdown
± (0.25 % R + 0.05 )
SIZE 0402 to 2512
No visible damage
REQUIREMENTS
no visible damage
no visible damage
1 to 10 M
± (0.5 % R + 0.05 )
±0.5 % R + 0.05)
Document Number: 20035
www.vishay.com/doc?91000
± (1 % R + 0.05 )
± (2 % R + 0.1 )
± (2 % R + 0.1 )
± (4 % R + 0.1 )
OR BETTER
± 200 ppm/K
STABILITY
CLASS 2
Revision: 08-Mar-11
± 5 %