96R1A-R22-A22 Bourns Inc., 96R1A-R22-A22 Datasheet - Page 2
![Panel Mount Potentiometers 5/8 250K 10% Square Single Turn](/photos/30/49/304900/93_l_sml.jpg)
96R1A-R22-A22
Manufacturer Part Number
96R1A-R22-A22
Description
Panel Mount Potentiometers 5/8 250K 10% Square Single Turn
Manufacturer
Bourns Inc.
Type
Potentiometerr
Specifications of 96R1A-R22-A22
Resistance
250kohm
Power Rating
2W
Tolerance (+ Or -)
10%
Number Of Turns
1Turn
Technology
Cermet
Mounting Style
Panel
Termination Style
Pin
Operating Temp Range
-40C to 125C
Failure Rate
Not Required
Shaft Diameter (mm)
6mm
Product Diameter (mm)
Not Requiredmm
Product Length (mm)
34.7mm
Product Height (mm)
17.47mm
Product Depth (mm)
15.88mm
Temperature Coefficient
±150
Tolerance
10 %
Taper
Linear
Element Type
Cermet
Shaft Type
Slotted
Shaft Length
22 mm
Shaft Diameter
6 mm
Operating Temperature Range
- 40 C to + 125 C
Product
Panel Mount Potentiometers
Lead Free Status / RoHS Status
Not Compliant
Stop Strength (1/4 ” D shaft) .............................................................................................................................................45.19 N-cm (4 lb.-in.)
Mechanical Angle .................................................................................................................................................................................300 ° ±5 °
Torque
Single or Dual Section (A & R Bushings) .................................................................................................. 0.21 to 1.06 N-cm (0.3 to 1.5 oz.-in.)
Single or Dual Section (C & U Bushings) .................................................................................................. 0.14 to 1.06 N-cm (0.2 to 1.5 oz.-in.)
Weight (Single Section, Metal Bushing) ...............................................................................................................................12.7 grams nominal
Terminals .................................................................................................................................Printed circuit terminals, J-Hooks or solder lugs
Marking ..................................................................................Manufacturer’s trademark, date code, resistance, manufacturer’s part number
Ganging (Multiple Section Potentiometers) .............................................................................................................................2 cups maximum
Hardware ...................One lockwasher and one mounting nut is shipped with each potentiometer, except where noted in the part number.
NOTE:
1
Model 91 PC Pin Terminals, In-Line
At room ambient: +25 °C nominal and 50 % relative humidity nominal, except as noted.
Product Dimensions
Mechanical Characteristics
Starting ........................................................................................................................................... 0.3 max. above average running torque
Running Torque
Mounting .............................................................................................................................................1.7-2.0 N-m (15-18 lb.-in.) maximum
Variation ...................................................................................................................... 0.35 N-cm (0.5 oz.-in.) maximum in 45 ° shaft travel
(Each Additional Section) ....................................................................................................................................................4 grams nominal
Soldering Condition ...........................................Recommended hand soldering using Sn95/Ag5 no clean solder, 0.025 ” wire diameter.
TOLERANCES EXCEPT AS SHOWN: DECIMAL .XXX ±
Model 96 - 5/8 ” Square Sealed Single-Turn Panel Control
DIMENSIONS:
Performance specifi cations do not apply to units subjected to printed circuit board immersion cleaning processes.
MOUNTING
SURFACE
1
2
3
(1/8 ” D shaft) .............................................................................................................................................33.89 N-cm (3 lb.-in.)
R1
(INCHES)
MM
(.510 ± .008)
(.435 ± .008)
12.95 ± .203
11.05 ± 0.20
(.031 ± .010)
0.79 ± .025
L
SEE HOW TO ORDER
CHART FOR
BUSHING OPTIONS.
1
SEE
NEXT PAGE
FOR SHAFT
OPTIONS.
(.015 )
.XX ±
.381
(.38)
FRACTION ± 1/64
9.65
(.093 ± .003)
2.36 ± 0.08
Maximum temperature 399 °C (750 °F) for 3 seconds. Immersion wash is not recommended.
(.540 ± .015)
(.054 ± .003)
13.72 ± 0.38
1.37 ± 0.08
ANGLE ±5 °
DIA.
R
“A” STYLE
A.R. LUG
(.047)
1.19
(.100)
2.54
(.100)
2.54
BACK VIEW
(.625)
15.88
(.602 ± .022)
15.29 ± 0.56
(.030 ± .002)
0.76 ± 0.05
TYP.
(.312)
(.375)
7.92
9.53
Customers should verify actual device performance in their specifi c applications.
Shaft Flat Orientation
Specifi cations are subject to change without notice.
120 ° ± 5 ° STD.
FLAT ORIENTATION
(SHAFT AT CCW END)
CCW
1
POTENTIOMETER
2
3