1804030-1 TE Connectivity, 1804030-1 Datasheet

1804030-1

Manufacturer Part Number

1804030-1

Description

EXTRACTION TOOL ASSY

Manufacturer

TE Connectivity

Type

Toolr

Datasheets

1.1804030-1.pdf (2 pages)

2.1804030-1.pdf (2 pages)

3.1804030-1.pdf (1 pages)

Specifications of 1804030-1

Rohs Compliant

Application

Universal MATE-N-LOK® II connectors

Tool Type

Extraction Tool

Lead Free Status / RoHS Status

RoHS Not Applicable

Available stocks

Company

Part Number

Manufacturer

Quantity

Price

Company:

Bonase Electronics (HK) Co., Limited

Part Number:

1804030-1

Manufacturer:

Quantity:

Current page: 1 of 2
Download datasheet (103Kb)

PROPER USE GUIDELINES

1. INTRODUCTION

Extraction Tool 1804030–1 is designed to remove pin

and socket contacts from Universal MATE–N–LOK

connectors (refer to Instruction Sheet 408–7714) and

Universal MATE–N–LOK II connectors (refer to

Instruction Sheet 408–3200).

2. DESCRIPTION

The extraction tool features an extraction tip, an

interlock lever, and handle. The extraction tip is

designed to enter the contact cavity at the mating

face of connector and release the contact from the

connector. When the extraction tip is bottomed, and

the handle is pushed toward the connector, a plunger

within the handle pushes the contact free from the

connector.

NOTE

Dimensions in this instruction sheet are in

millimeters [with inches in brackets]. Figures and

illustrations are for reference only and are not

drawn to scale.

Extraction Tool Assembly 1804030-1

Figure 1

3. EXTRACTION PROCEDURE

1. For the Universal MATE–N–LOK connector,

grasp the wire of the contact to be removed, and

push it toward the mating end of the connector to

release the contact locking lances. Hold in place.

For the Universal MATE–N–LOK II connector,

move the rear housing latch to the pre–stage

position.

2. Depress, and hold the interlock lever. Insert the

extraction tip into the contact cavity of the contact

to be removed, and slide it over the contact. Refer

to Figure 1.

3. For the Universal MATE–N–LOK connector,

(while pushing the wire toward the tool) continue to

insert the extraction tip until it bottoms.

For the Universal MATE–N–LOK II connector,

continue to insert the extraction tip until it rests on

the retention shoulder of the contact.

4. Release the interlock lever, and push the tool

handle FULLY; thereby, pushing the contact slightly

out of the wire end of the connector.

www.tycoelectronics.com

408-10049

Related parts for 1804030-1

1804030-1 Summary of contents

Page 1

... When the extraction tip is bottomed, and the handle is pushed toward the connector, a plunger within the handle pushes the contact free from the connector. E Extraction Tool Assembly 1804030-1 Figure 1 3. EXTRACTION PROCEDURE 1. For the Universal MATE–N–LOK connector, grasp the wire of the contact to be removed, and push it toward the mating end of the connector to release the contact locking lances ...

Page 2

... Extraction Tool Assembly 1804030-1 5. Pull the wire until the contact is out of the connector. NOTE If the extracted contact is NOT damaged, it may be re-inserted. For a contact removed from a i Universal MATE-N-LOK connector, the locking lances MUST be reset to their original position as shown in Figure 2. DO NOT re-use a defective or damaged contact ...

Related keywords

1804030-1 datasheet
1804030-1 data sheet
1804030-1 pdf datasheet
1804030-1 component
1804030-1 part
1804030-1 distributor
1804030-1 RoHS
1804030-1 datasheet download