DRHP-12715A-26 RDI Electronics, Inc., DRHP-12715A-26 Datasheet - Page 3

• Manufacturer Part Number: DRHP-12715A-26
• Manufacturer: RDI Electronics, Inc.

Specifications of DRHP-12715A-26

• Lead Free Status / RoHS Status: Supplier Unconfirmed

5. MOUNTING CHARACTERISTICS
6. ENDURANCE
4
5
2
1
3
1
2
3
APPEARANCE
RESISTANCE TO
SOLDERING HEAT
ITEM/STANDARD
ITEM/STANDARD
SOLDER ABILITY
LIFE TEST
HOT AIR
REFLOW OR IR
REFLOW FOR
SMD CURING
PROCESS
VIBRATION
TEST
THERMAL
SHOCK
SALT
WATER
SPRAY
SOLDER EACH OF THE PLUG AND RECEPTACLE CONNECTOR TO THE
P.C. BOARD THEN PLACE EACH OF THE P.C. BOARD ONTO THE
PUSH-ON/PULL-OFF MACHINE,THEN DO MATING/UNMATING 5000
CYCLES ALONG THE AXIS AT SPEED OF 100mm PER MIN.
VISUAL
EACH TERMINAL SHALL BE CONNECTED IN SERIES AND THEN 100mA DC SHALL
BE CARRIED.
BOARD,THEN MATE THEM TOGETHER. PLACE THE MATED CONNECTOR FIRMLY
FREQUENCY: 10Hz-55Hz-10Hz/MIN.
DIRECTION: ALONG THREE MUTUALLY PERPENDICULAR DIRECTION
BOARD,THEN MATE THEM TOGETHER,AND EXPOSE THEM TO THE FOLLOWING
ENVIRONMENTAL CONDITION.
NUMBER OF EXPOSURE: 5 CYCLES
IT SHALL BE SUBJECTED TO STANDARD ATMOSPHERIC CONDITION FOR 1 TO
BOARD,THEN MATE THEM TOGETHER,AND EXPOSE THEM TO THE FOLLOWING
ENVIRONMENTAL CONDITION.
DENSITY OF SALT WATER: 5± 1 %
DURATION: 4 HR ± 15 MIN.
IT SHALL BE SUBJECTED TO STANDARD ATMOSPHERIC CONDITION 1 H. AFTER
REMOVING THE SALT DEPOSITS.
SOLDER EACH OF PLUG AND RECEPTACLE CONNECTOR TO THE P.C.
ON THE VIBRATOR AND APPLY THE FOLLOWING CONDITION SHALL BE DONE
SWEEP TIME: 2 HOURS ALONG EACH DIRECTION, A TOTAL 6 HOURS
AMPLITUDE: 1.52mm
SOLDER EACH OF THE PLUG AND RECEPTACLE CONNECTOR TO THE P.C.
TEMPERATURE: -55°C ± 3°C(30 min), STANDARD ATMOSPHERIC
CONDITION(10-15 MIN) TO 85°C± 2°C (30 MIN.
CONDITION(10-15 MIN.) TRANSITION TIMES: 5 MIN. MAX.
2H,AFTER WHICH MEASUREMENTS SHALL BE MADE.
SOLDER EACH OF THE PLUG AND RECEPTACLE CONNECTOR TO THE P.C.
TEMPERATURE: 35°C ± 2°C
IMMERSE THE SOLDER PIN OF THE CONNECTOR IN THE SOLDER
BATH AT 230°C ± 5°C FOR 5± 0.5 SECONDS. AFTER DIPPED THE
PIN IN THE FLUX OF RAM OR R TYPE FOR 5 SECONDS.
PLACE THE CONNECTOR ON THE P.C. BOARD AND EXPOSE THEM TO THE
REFLOW OVEN AND APPLY THE FOLLOWING CONDITION.
ROOM 1: PREHEAT TEMPERATURE 150°C -170°C FOR 60 SECS.
ROOM 2: PREHEAT TEMPERATURE 170°C -190°C FOR 60 SECS.
ROOM 3 : REFLOW TEMPERATURE 200°C -240°C -200°C FOR -30-40 SEC.
(FOR 240°C ONLY 3-5 SECONDS)
PLACE THE CONNECTOR ON THE P.C. BOARD, THEN IMMERSE THE
SOLDER PIN UP TO THE SURFACE OF THE BOARD IN THE SOLDER
BATH AT 260°C ± 5°C FOR 10 SECONDS.
TEST CONDITIONS
TEST CONDITIONS
STANDARD ATMOSPHERIC
RESISTANCE VALUE AFTER TEST
Rf
APPEARANCE SHALL NOT BE
CRACKING AND PIN LOOSENS.
NO PEELING OFF THE
PLATING,DEFORMATION OF THE
BASE OR DAMAGE.
MORE THAN 95 % OF THE DIPPED
ELECTRICAL CHARACTERISTICS
SURFACE SHALL BE WET WITH
SOLDER
WITHOUT DEFORMATION OF
CASE OR EXCESSIVE LOOSENS.
SHALL BE SATISFIED.
DISTINCT DAMAGE.
MORE THAN 95 % OF THE
MOUNTING PIN SURFACE SHALL
BE WET SOLDER
APPEARANCE SHALL NOT BE
1. NO ELECTRICAL
RESISTANCE VALUE AFTER TEST
Rf=
APPEARANCE SHALL NOT BE
CRACKING AND PIN LOOSENS.
BY VISUAL INSPECTION
WITHOUT NOTICEABLE RUST.
RESISTANCE VALUE AFTER TEST
Rf=
2. LOOSEN AND
3. THE CONTACT RESISTANCE
Rf = 2 Ri.
THAN 1 u SEC. SHALL OCCUR.
PART AND OTHER
DISCONTINUITY GREATER
BREAKAGE OF THE PLASTIC
DETRIMENTAL DAMAGE SHALL
NOT BE OBSERVED.
Ri 20m OHM
SPECIFICATION
SPECIFICATION
Ri ± 20m OHM
Ri ± 20m OHM
4
5
6
7
HUMIDITY
(STEADY
STATE)
DRY HEAT
SHOCK
COLD
THE CONNECTOR HOUSING SHALL BE STORE AT
TEMPERATURE OF 85± 2°C FOR 96 HOURS ,THEN IT
SHALL BE SUBJECTED TO STANDARD ATMOSPHERIC
CONDITION FOR 1 H. AFTER WHICH MEASUREMENTS
SHALL BE MADE.
SOLDER EACH OF THE PLUG AND RECEPTACLE
CONNECTOR TO THE P.C. BOARD,THEN MATE THEM
TOGETHER,AND EXPOSE THEM TO THE FOLLOWING
ENVIRONMENTAL CONDITION.
TEMPERATURE: -25°C± 3°C
DURATION: 48± 1 HOUR
IT SHALL BE SUBJECTED TO STANDARD ATMOSPHERIC
CONDITION FOR 1 HOUR AFTER WHICH MEASUREMENTS
SHALL BE MADE.
SOLDER EACH OF THE PLUG AND RECEPTACLE
CONNECTOR TO THE P.C. BOARD,THEN MATE THEM
ENVIRONMENTAL CONDITION.
RELATIVE HUMIDITY: 90 % - 95 %
DURATION: 96 HOURS
IT SHALL BE SUBJECTED TO STANDARD ATMOSPHERIC
CONDITION FOR 1 HOUR AFTER WHICH MEASUREMENTS
SHALL BE MADE.
SOLDER EACH OF THE PLUG AND RECEPTACLE
CONNECTOR TO THE P.C. BOARD THEN MATE THEM
TOGETHER,THEN EACH TERMINAL SHALL BE
CONNECTED IN SERIES AND THEN DC 100 mA BE
CARRIED.
PLACE THE MATED CONNECTOR FIRMLY ON THE SHOCK
MACHINE AND APPLY THE FOLLOWING CONDITION TO BE
TESTED.
PEAK ACCELERATION: 50G MAX.
DURING OF THE PLUS: 11m SECOND.
WAVE: HALF SINUSOIDAL
NUMBER OF DROPS: 18 TIMES
DIRECTION: ALONG 3 MUTUALLY PERPENDICULAR
DIRECTION.
TOGETHER,AND EXPOSE THEM TO THE FOLLOWING
TEMPERATURE: 50± 2°C
RDI, Inc. 400 Columbus Avenue Valhalla, NY 10595
Research Develop Innovate
RESISTANCE VALUE AFTER
TEST
Rf = TWICE OF Ri.
BE DISTINCT DAMAGE.
APPEARANCE SHALL NOT
RESISTANCE VALUE AFTER
TEST Rf = TWICE OF Ri.
APPEARANCE SHALL NOT
BE DISTINCT DAMAGE.
THE INSULATION
RESISTANCE AND
DIELECTRIC STRENGTH
MUST COINCIDE
PREVIOUSLY
SPECIFICATION.
RESISTANCE VALUE AFTER
TEST Rf = TWICE OF Ri.
APPEARANCE SHALL NOT
BE DISTINCT DAMAGE.
RESISTANCE VALUE AFTER
Rf = TWICE OF Ri.
BE DISTINCT DAMAGE.
NO ELECTRICAL
DISCONTINUITY GREATER
OCCUR
TEST
APPEARANCE SHALL NOT
THAN 1 u SEC SHALL