MKT1813410255 Vishay, MKT1813410255 Datasheet - Page 10

• Manufacturer Part Number: MKT1813410255
• Manufacturer: Vishay

Specifications of MKT1813410255

• Tolerance (+ Or -): 10%
• Voltage: 250VDC/160VAC
• Temp Coeff (dielectric): PLYE
• Mounting Style: Through Hole
• Construction: Axial
• Failure Rate: Not Required
• Seated Plane Height: Not Requiredmm
• Product Diameter (mm): 6mm
• Product Height (mm): Not Requiredmm
• Product Depth (mm): Not Requiredmm
• Product Length (mm): 14mm
• Lead Spacing (nom): Not Requiredmm
• Lead Diameter (nom): 0.7mm
• Operating Temp Range: -55C to 100C
• Capacitance: .1uF
• Package / Case: Not Required
• Lead Free Status / RoHS Status: Compliant

MKT 1813
Vishay Roederstein
INSPECTION REQUIREMENTS
General Notes:
Sub-clause numbers of tests and performance requirements refer to the “Sectional Specification, Publication IEC 60384-2 and
Specific Reference Data”.
Group C Inspection Requirements
www.vishay.com
26
SUB-CLAUSE NUMBER AND TEST
SUB-GROUP C1A PART OF SAMPLE
OF SUB-GROUP C1
4.1
4.3.1
4.3
4.4
4.14
4.4.2
SUB-GROUP C1B PART OF SAMPLE
OF SUB-GROUP C1
4.6.1
4.6
4.7
4.7.2
Dimensions (detail)
Initial measurements
Robustness of terminations
Resistance to soldering heat
Component solvent resistance
Final measurements
Initial measurements
Rapid change of temperature
Vibration
Final inspection
For technical questions, contact: [e-mail]
CONDITIONS
Capacitance
Tangent of loss angle:
Tensile: Load 10 N; 10 s
Bending: Load 5 N; 4 x 90°
Method: 1A
Isopropylalcohol at room temperature
Method: 2
Visual examination
Capacitance
Tangent of loss angle
Capacitance
Tangent of loss angle:
θA = - 55 °C
θB = + 100 °C
5 cycles
Duration t = 30 min
Visual examination
Mounting:
See section “Mounting” of this specification
Procedure B4
Visual examination
For C ≤ 470 nF at 100 kHz or
for C > 470 nF at 10 kHz
Solder bath: 280 °C ± 5 °C
Duration: 10 s
Immersion time: 5 ± 0.5 min
Recovery time: Min. 1 h, max. 2 h
For C ≤ 470 nF at 100 kHz or
for C > 470 nF at 10 kHz
Frequency range: 10 Hz to 55 Hz
Amplitude: 0.75 mm or
Acceleration 98 m/s²
(whichever is less severe)
Total duration 6 h
DC Film Capacitor
MKT Axial Type
PERFORMANCE REQUIREMENTS
As specified in Chapters “General data” of
this specification
No visible damage
No visible damage
Legible marking
|ΔC/C| ≤ 2 % of the value measured initially
Increase of tan δ
Compared to values measured in 4.3.1
No visible damage
No visible damage
≤ 0.005 for:
C ≤ 100 nF or
≤ 0.010 for:
100 nF < C ≤ 220 nF or
≤ 0.015 for:
220 nF < C ≤ 470 nF and
≤ 0.003 for:
C > 470 nF
Document Number: 26013
Revision: 08-Dec-08