64YR100KLF BI Technologies, 64YR100KLF Datasheet
64YR100KLF
Manufacturer Part Number
64YR100KLF
Description
Trimmer Resistors - Multi Turn 100K ohm 10% 1/4 squ 12 turn
Manufacturer
BI Technologies
Type
Trimmerr
Datasheet
1.64YR100KLF.pdf
(4 pages)
Specifications of 64YR100KLF
Resistance
100kohm
Power Rating
1/4W
Tolerance (+ Or -)
10%
Number Of Turns
12Turn
Technology
Cermet
Mounting Style
Through Hole
Termination Style
Pin
Operating Temp Range
-65C to 150C
Failure Rate
Not Required
Shaft Diameter (mm)
1.78mm
Product Diameter (mm)
Not Requiredmm
Product Length (mm)
6.35mm
Product Height (mm)
7.88mm
Product Depth (mm)
4.19mm
Temperature Coefficient
±100
Product
Trimmer Resistors - Multi Turn
Lead Free Status / RoHS Status
Compliant
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
64YR100KLF
Manufacturer:
BCK
Quantity:
450
MODEL 64
1/4” Square
Multiturn
Cermet Trimming
Potentiometer
E L E C T R I C A L
Standard Resistance Range, Ohms
Standard Resistance Tolerance
Input Voltage, Maximum
Slider Current, Maximum
Power Rating, Watts
End Resistance, Maximum
Actual Electrical Travel, Turns, Nominal
Dielectric Strength
Insulation Resistance, Minimum
Resolution
Contact Resistance Variation, Maximum
E N V I R O N M E N T A L
Seal
Temperature Coefficient, Maximum
Operating Temperature Range
Thermal Shock
Moisture Resistance
Shock, 6ms Sawtooth
Vibration
High Temperature Exposure
Rotational Life
Load Life at 0.25 Watts
Resistance to Solder Heat
M E C H A N I C A L
Mechanical Stops
Torque, Starting Maximum
Weight, Nominal
Fluorinert® is a registered trademark of 3M Company.
Specifications subject to change without notice.
1-35
Ten 24 hour cycles (1% RT, IR 1,000 Megohms Min.)
5 cycles, –65°C to +150°C (1% RT, 1% VR)
100mA or within rated power, whichever is less
20G’s, 10 to 2,000 Hz (1% RT, 1% VR)
200Vdc or rms not to exceed power rating
250 hours at 125°C (2% RT, 2% VR)
1% or 1 Ohms, whichever is greater
0.25 at 85°C derating to 0 at 150°C
1,000 hours at 85°C (2% RT)
85°C Fluorinert® (No Leaks)
260°C for 10 sec. (1% RT)
100G’s (1% RT, 1% VR)
Clutch action, both ends
.014 oz. (0.40 grams)
200 cycles (2% RT)
3 oz.-in. (0.021 N-m)
Essentially infinite
–65°C to +150°C
1,000 Megohms
±100ppm/°C
Model 64
10 to 1Meg
900Vrms
2 Ohms
±10%
12
1
Related parts for 64YR100KLF
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
RES,Cermet,100Ohms,200WVDC,10+/-% Tol,2516-Case
Manufacturer:
BI TECHNOLOGIES/TT ELECTRONICS
Part Number:
Description:
RES,Cermet,10Ohms,200WVDC,10+/-% Tol,2516-Case
Manufacturer:
BI TECHNOLOGIES/TT ELECTRONICS
Part Number:
Description:
Manufacturer:
BI Technologies
Datasheet:
Part Number:
Description:
Dual In-Line Thick Film Resistor Network
Manufacturer:
BI Technologies
Part Number:
Description:
Manufacturer:
BI Technologies
Datasheet:
Part Number:
Description:
Manufacturer:
BI Technologies
Datasheet:
64YR100KLF Summary of contents
Page 1
MODEL 64 1/4” Square Multiturn Cermet Trimming Potentiometer Standard Resistance Range, Ohms Standard Resistance Tolerance Input Voltage, Maximum Slider Current, Maximum Power Rating, Watts End Resistance, Maximum Actual Electrical Travel, ...
Page 2
Model 64W and 64Y Metal Adjustment Screw .070 .005 Dia. With Slot 1.78 0.13 .020 .020 Min. Wide ...
Page 3
Model 64X and 64Z Standard Marking On This Surface Model 64Z C L .10 .10 2.54 2.54 ...
Page 4
Standard: Tubes All units oriented with #1 pin to same side. Pin Style Magazine Width Height Length Capacity Option: Tape & Reel, Ammo Pack (Available only for 64Y and 64Z) All ...