1-1375820-1 TE Connectivity, 1-1375820-1 Datasheet - Page 5

• Manufacturer Part Number: 1-1375820-1
• Description: CST-100 II HOUSING 11 POS
• Manufacturer: TE Connectivity
• Type: Housingr

Specifications of 1-1375820-1

• Wire Gauge: 22-26
• Number Of Contacts: 11POS
• Number Of Contact Rows: 1
• Body Orientation: Straight
• Pitch (mm): 2.54mm
• Gender: RCP
• Housing Material: Polymer
• Operating Temp Range: -55C to 105C
• Current Rating (max): 4/ContactA
• Voltage Rating Max: 250VAC
• Housing Color: White
• Product Height (mm): 6.6mm
• Product Depth (mm): 12.95mm
• Rohs Compliant: YES
• Connector Type: Housing
• Product Line: CST-100 II
• Termination Method To Wire/cable: Crimp
• Mating Connector Lock: With
• Four Points Of Contact: Without
• Shrouded: No
• Mounting Ears: Without
• Panel Mount Retention: Without
• Number Of Positions: 11
• Centerline (mm [in]): 2.54 [0.100]
• Cable Exit Angle: 180°
• Contact Type: Socket
• Connector Style: Receptacle
• Mating Alignment: With
• Ul Flammability Rating: UL 94V-0
• Rohs/elv Compliance: RoHS compliant, ELV compliant
• Lead Free Solder Processes: Not relevant for lead free process
• Rohs/elv Compliance History: Always was RoHS compliant
• Application Use: Wire-to-Board
• Lead Free Status / RoHS Status: Compliant

4.
4.1.
4.2.
4.3.
4.4.
Rev D
QUALITY ASSURANCE PROVISIONS
Qualification Testing
A.
B.
Requalification Testing
If changes significantly affecting form, fit or function are made to the product or manufacturing process,
product assurance shall coordinate requalification testing, consisting of all or part of the original testing
sequence as determined by development/product, quality and reliability engineering.
Acceptance
Acceptance is based on verification that the product meets the requirements of Figure 1. Failures
attributed to equipment, test setup or operator deficiencies shall not disqualify the product. If product
failure occurs, corrective action shall be taken and specimens resubmitted for qualification. Testing to
confirm corrective action is required before resubmittal.
Quality Conformance Inspection
The applicable quality inspection plan shall specify the sampling acceptable quality level to be used.
Dimensional and functional requirements shall be in accordance with the applicable product drawing
and this specification.
Specimen Selection
Specimens shall be prepared in accordance with applicable Instruction Sheets and shall be
selected at random from current production. Test groups 1 and 2 shall each consist of: 6, 28
position assemblies; 60 terminals crimped to 22 AWG wire; and 60 terminals crimped to 26 AWG
wire. Test groups 3 and 4 shall each consist of: 5, 28 position assemblies and 100 terminals
crimped to 22 AWG wire. Test group 5 shall consist of: 5, 28 position assemblies; 5, 3 position
assemblies; 5, 10 position assemblies; 5, 18 position assemblies; and 295 terminals crimped to 22
AWG wire. Test group 6 shall consist of 25 specimens of each wire size. Specimens for additional
testing in test group 1 shall consist of 48, 6 position assemblies with the following plating
configurations for CST-100 II contact to header: 15 µin Au to 15 µin Au; 15 µin Au to 15 µin PdNi;
15 µin PdNi to 15 µin Au; 15 µin PdNi to 15 µin PdNi; 30 µin Au to 30 µin Au; 30 µin Au to 30 µin
PdNi; 30 µin PdNi to 30 µin Au; and 30 µin PdNi to 30 µin PdNi.
Test Sequence
Qualification inspection shall be verified by testing specimens as specified in Figure 2.
108-1948
5 of 8