NCP4641H080T1G ON Semiconductor, NCP4641H080T1G Datasheet - Page 12

• Manufacturer Part Number: NCP4641H080T1G
• Description: IC REG LDO 50MA 8.0V SOT89-6
• Manufacturer: ON Semiconductor

Specifications of NCP4641H080T1G

• Number Of Outputs: 1
• Output Type: Adjustable
• Output Voltage: 8 V
• Output Current: 100 mA, 120 mA, 150 mA
• Load Regulation: 35 mV
• Dropout Voltage (max): 0.35 V
• Input Voltage Max: 36 V
• Maximum Operating Temperature: + 150 C
• Minimum Operating Temperature: - 40 C
• Package / Case: SOT-89-5
• Maximum Power Dissipation: 900 mW
• Mounting Style: SMD/SMT
• Voltage Regulation Accuracy: 2 %
• Regulator Topology: Positive Fixed
• Voltage - Output: 8V
• Voltage - Input: Up to 36V
• Voltage - Dropout (typical): 0.2V @ 20mA
• Number Of Regulators: 1
• Current - Output: 150mA (Min)
• Current - Limit (min): -
• Operating Temperature: -40°C ~ 150°C
• Mounting Type: Surface Mount
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

in Figure 32.
Input Decoupling Capacitor (C1)
input line is long and has high impedance or if more stable
operation is needed, input capacitor C1 should be connected
as close as possible to the IC. Recommended range of input
capacitor value is 100 nF to 10 mF.
Output Decoupling Capacitor (C2)
but if faster response and higher stability reserve is needed,
output capacitor should be connected as close as possible to
the device. Recommended range of output capacitance is
100 nF to 10 mF. Larger values of output capacitance and
lower ESR improves dynamic parameters.
Enable Operation
on and off. The device is activated when high level is
†For information on tape and reel specifications, including part orientation and tape sizes, please refer to our Tape and Reel Packaging
*To order other package and voltage variants, please contact your ON Semiconductor sales representative.
VIN
ORDERING INFORMATION
Specifications Brochure, BRD8011/D.
NCP4641H030T1G
NCP4641H050T1G
NCP4641H080T1G
A typical application circuit for NCP4641 series is shown
The device is stable without any input capacitance, but if
The NCP4641 can work stable without output capacitor,
The enable pin CE may be used for turning the regulator
100 n
C1
Figure 32. Typical Application Schematic
Device
VIN
CE
NCP4641x
GND
VOUT
Nominal Output
Voltage
3.0 V
5.0 V
8.0 V
APPLICATION INFORMATION
100 n
C 2
Description
Enable High
Enable High
Enable High
http://onsemi.com
VOUT
12
connected to CE pin. Do not keep CE pin not connected or
between VCEH and VCEL voltage levels. Otherwise output
voltage would be unstable or indefinite and unexpected
would flow internally.
Thermal
necessary to provide some thermal relief. The maximum
power dissipation supported by the device is dependent
upon board design and layout. Mounting pad configuration
on the PCB, the board material, and also the ambient
temperature affect the rate of temperature increase for the
part. When the device has good thermal conductivity
through the PCB the junction temperature will be relatively
low in high power dissipation applications.
stops operation of regulator, if junction temperature is
higher than 150°C. After that, when junction temperature
decreases below 125°C, the operation of voltage regulator
would restart. While high power dissipation condition is, the
regulator starts and stops repeatedly and protects itself
against overheating.
PCB Layout
number 2, 4 and 5 of SOIC6−TL must be wired to the GND
plane while it is mounted on board. Make VIN and GND
lines sufficient. If their impedance is high, noise pickup or
unstable operation may result. Connect capacitors C1 and
C2 as close as possible to the IC, and make wiring as short
as possible.
As a power across the IC increase, it might become
The IC includes internal thermal shutdown circuit that
Pins number 2 and 4 of SOT89−5 package and pins
Marking
M030
M050
M080
(Pb−Free)
(Pb−Free)
(Pb−Free)
SOT89−5
SOT89−5
SOT89−5
Package
1000 / Tape & Reel
1000 / Tape & Reel
1000 / Tape & Reel
Shipping
†