EVAL-ADT7X10EBZ Analog Devices Inc, EVAL-ADT7X10EBZ Datasheet
![Evaluation Board I.c.](/photos/9/19/91955/eval-adt7410ebz_sml.jpg)
EVAL-ADT7X10EBZ
Specifications of EVAL-ADT7X10EBZ
EVAL-ADT7410EBZ
Related parts for EVAL-ADT7X10EBZ
EVAL-ADT7X10EBZ Summary of contents
Page 1
FEATURES 13- or 16-bit user selectable temperature-to-digital converter Temperature accuracy: ±0.5°C from −40°C to +105°C No temperature calibration/correction required by user Power saving 1 sample per second (SPS) mode Fast first conversion on power- C-compatible ...
Page 2
ADT7410 TABLE OF CONTENTS Features .............................................................................................. 1 Applications ....................................................................................... 1 General Description ......................................................................... 1 Functional Block Diagram .............................................................. 1 Revision History ............................................................................... 2 Specifications ..................................................................................... Timing Specifications ............................................................ 4 Absolute Maximum Ratings ............................................................ 5 ESD Caution ...
Page 3
SPECIFICATIONS T = −55°C to +150° 2 5.5 V, unless otherwise noted Table 1. Parameter Min TEMPERATURE SENSOR AND ADC 1 Accuracy ADC Resolution Temperature Resolution 13-Bit 16-Bit Temperature Conversion Time Fast Temperature Conversion ...
Page 4
ADT7410 TIMING SPECIFICATIONS T = −55°C to +150° 2 5.5 V, unless otherwise noted. All input signals are specified with rise time ( (10 and timed ...
Page 5
ABSOLUTE MAXIMUM RATINGS Table 3. Parameter V to GND DD SDA Voltage to GND SCL Output Voltage to GND A0 Input Voltage to GND A1 Input Voltage to GND CT and INT Output Voltage to GND ESD Rating (Human Body ...
Page 6
ADT7410 PIN CONFIGURATION AND FUNCTION DESCRIPTIONS Table 4. Pin Function Descriptions Pin No. Mnemonic Description 1 SCL Serial Clock Input. The serial clock is used to clock in and clock out data to and from any register ...
Page 7
TYPICAL PERFORMANCE CHARACTERISTICS 1.0 0.8 0.6 MAX ACCURACY LIMITS 0.4 0.2 0 –0.2 –0.4 –0.6 MAX ACCURACY LIMITS –0.8 –1.0 –60 –40 – TEMPERATURE (°C) Figure 5. Temperature Accuracy 1.0 0.8 MAX ACCURACY ...
Page 8
ADT7410 0.30 I CONTINUOUS CONVERSION DD 0.25 0.20 0.15 0.10 I 1SPS DD 0.05 0 2.5 3.0 3.5 4.0 4.5 SUPPLY VOLTAGE (V) Figure 9. Average Operating Supply Current vs. Supply Voltage at 25° ...
Page 9
THEORY OF OPERATION CIRCUIT INFORMATION The ADT7410 is a 13-bit digital temperature sensor that is extend- able to 16 bits for greater resolution. An on-board temperature sensor generates a voltage proportional to absolute temperature, which is compared to an internal ...
Page 10
ADT7410 ONE-SHOT MODE Setting Bit and Bit the configuration register (Register Address 0x03) enables the one-shot mode. When this mode is enabled, the ADT7410 immediately completes a conversion and then goes into shutdown ...
Page 11
SHUTDOWN The ADT7410 can be placed in shutdown mode by writing 1 to Bit 5 and 1 to Bit 6 of the configuration register (Register Address 0x03), in which case the entire IC is shut down and no further conversions ...
Page 12
ADT7410 TEMPERATURE DATA FORMAT One LSB of the ADC corresponds to 0.0625°C in 13-bit mode. The ADC can theoretically measure a temperature range of 255°C, but the ADT7410 is guaranteed to measure a low value temperature limit of −55°C to ...
Page 13
REGISTERS The ADT7410 contains 14 registers: • Nine temperature registers • A status register • register • A configuration register • An address pointer register • A software reset All registers are eight bits wide. The temperature value ...
Page 14
ADT7410 STATUS REGISTER This 8-bit read-only register reflects the status of the overtempera- ture and undertemperature interrupts that can cause the CT and INT pins to go active. It also reflects the status of a temperature conversion operation. The interrupt ...
Page 15
T SETPOINT REGISTERS HIGH The T setpoint MSB and T setpoint LSB registers store HIGH HIGH the overtemperature limit value. An overtemperature event occurs when the temperature value stored in the temperature value register exceeds the value stored in this ...
Page 16
ADT7410 T SETPOINT REGISTER HYST This 8-bit read/write register stores the temperature hysteresis value for the and T temperature limits. The HIGH LOW CRIT temperature hysteresis value is stored in straight binary format using four LSBs. ...
Page 17
SERIAL INTERFACE TO INTERRUPT PIN ON MICROCONTROLLER Control of the ADT7410 is carried out via the I serial interface. The ADT7410 is connected to this bus as a slave and is under the control of a master device. 2 Figure ...
Page 18
ADT7410 WRITING DATA It is possible to write either a single byte of data or two bytes to the ADT7410, depending on which registers are to be written. Writing a single byte of data requires the serial bus address, the ...
Page 19
READING DATA Reading data from the ADT7410 is done in a single data byte operation for the configuration register, the status register, the T register, and the ID register. A two data byte read HYST operation is needed for the ...
Page 20
ADT7410 1 SCL SDA START ADT7410 DEVICE ADDRESS 1 SR SCL SDA 1 0 REPEAT ADT7410 DEVICE ADDRESS START NOTES 1. A START CONDITION AT THE BEGINNING IS DEFINED AS A HIGH-TO-LOW TRANSITION ON SDA WHILE SCLK ...
Page 21
INT AND CT OUTPUTS The INT and CT pins are open-drain outputs, and both pins require a 10 kΩ pull-up resistor UNDERTEMPERATURE AND OVERTEMPERATURE DETECTION The INT and CT pins have two undertemperature/overtemperature modes: comparator mode ...
Page 22
ADT7410 (COMPARATOR MODE) POLARITY = ACTIVE LOW (INTERRUPT MODE) POLARITY = ACTIVE LOW (COMPARATOR MODE) POLARITY = ACTIVE HIGH (INTERRUPT MODE) POLARITY = ACTIVE HIGH Figure 20. INT Output Temperature Response Diagram for T TEMPERATURE –13°C –14°C –15°C –16°C –17°C ...
Page 23
APPLICATIONS INFORMATION THERMAL RESPONSE TIME The time required for a temperature sensor to settle to a specified accuracy is a function of the thermal mass of the sensor and the thermal conductivity between the sensor and the object being sensed. ...
Page 24
... Temperature Accuracy ±0.5°C ±0.5°C ±0.5° Standard Specification as defined by Philips. D06560-0-4/09(0) Rev Page 0.50 (0.0196) 45° 0.25 (0.0099) 1.27 (0.0500) 0.40 (0.0157) 1 Package Description Package Option 8-Lead SOIC_N R-8 8-Lead SOIC_N R-8 8-Lead SOIC_N R-8 Evaluation Board 2 C Patent ...