CUB10000 Red Lion Controls, CUB10000 Datasheet - Page 3

• Manufacturer Part Number: CUB10000
• Description: Counter
• Manufacturer: Red Lion Controls

Specifications of CUB10000

• Lead Free Status / Rohs Status: RoHS Compliant part

DIMENSIONS, INSTALLATION, & BATTERY INSERTION
counter body to the back of the bezel. Then slide counter through the panel cut-
out. Install mounting clips on each side of counter body with mounting screws.
CUB 1
ELECTRICAL CONNECTIONS
count and control signal wires. A length of wire can act like an antenna and the
closer it is to a source of electrical noise, the more it becomes susceptible to
that noise.
1. Never run count or control signal wires in the same conduit or raceway with
ORDERING INFORMATION
BATTERY COVER REMOVAL & BATTERY INSERTION
For more information on Pricing, Enclosures & Panel Mount Kits refer to the RLC
Catalog or contact your local RLC distributor.
MODEL NO.
CUB 1
mating lock ramps on the cover. To remove, insert thumbnail and index finger
nail in the gaps between the upper and lower clasps and the battery cover, and
deflect the clasps slightly to clear the edges of the ramps while pulling out on
the cover. To replace cover, simply push into place until both clasps snap into
engagement with lock ramps.
CAUTION: Do not deflect clasps more than necessary to clear lock ramps.
After cutting opening in panel, slide the panel gasket over the rear of the
There are certain considerations that shoud be observed when running the
There are a few rules that should be followed when running these wires.
AC power lines, conductors that feed motors, solenoids, SCR controls,
heaters, etc.
HWK 1
HWK 2
CUB 1
CUB 2
The battery cover is held in place by upper and lower clasps that capture
Excessive deflection can cause clasps to break off.
BNA
ICA
DESCRIPTION
CUB 1 Miniature Electronic Counter
CUB 2 Gen. Purpose Industrial Electronic Counter
“N” Type Alkaline Batteries (Note 1)
CUB 1 Spare Hardware Kit (Note 2)
CUB 2 Spare Hardware Kit (Note 2)
Spare Input Connector & Terminal Wires (Note 3)
DIMENSIONS In inches (mm)
PART NUMBERS
HWK10000
HWK20000
CUB10000
CUB20000
BNA00000
ICA00000
3
CUB 2
out. To reinstall cover, insert left hand lips into case first, push cover to the left
until right hand lip drops down and cover snaps back into place. Install
batteries as shown below observing proper polarity.
Note: Push battery spring clips to the left (toward connector) to completely
2. Signal wires within enclosures should be routed as far away as possible from
3. When shielded wire is used, connect the shield to the common of the CUB
4. Mount the CUB in a panel that is grounded to the machine frame.
5. When using accessory devices such as LCMs or PSMs into the H.S. CNT.
the counter body so that the “Tang Ends” or “Tabs” wedge between the panel
opening and body as the screws are tightened.
CUB 2
Slide battery cover to the left until the right hand lip disengages and pops
free the batteries when removing or installing batteries. Conductive
rubber battery contacts can be torn from their retaining pins if batteries
are forced in.
contactors, control relays, transformers, and other noisy components.
unit, and leave the other end of the shield disconnected and insulated from
machine ground.
Input, the accessory devices should be mounted near the CUB Counter.
Make sure the side rails or tabs of the clips fit into the recesses in the side of
NOTES
1. Batteries NOT supplied with counters, order separately.
2. Counters supplied with required hardware. Includes 2 mounting
3. Counters supplied with connector body & white, yellow, & black
2 required per unit.
clips & screws, panel gasket, 2-wire nuts & blue terminal wire.
wires. Kit ICA includes connector body & one each of black,
white, blue, & yellow terminal wires.